Selecting the Sound Mode depending on the model | Samsung 4240

BN68-00597A-01 4/2/04 6:38 PM Page 42

Selecting the Sound Mode (depending on the model)

ENG

The “DUAL I-II” button displays/controls the processing and output of the audio signal. When power is switched on, the mode is automatically preset to either “DUAL-I ” or “Stereo”, depending on the current transmission.

		Type of broadcast	On-screen indication

		Regular broadcast	Mono (Normal use)
		(Standard audio)	Mono (Normal use)
		(Standard audio)

		Regular +	NICAM Mono ↔ Mono
	NICAM	NICAM Mono	NICAM Mono ↔ Mono
	NICAM	NICAM Mono
	Stereo	NICAM Stereo	NICAM Stereo ↔ Mono
			NICAM Stereo ↔ Mono
			(Forced mono)
			(Forced mono)

		NICAM DUAL-I/II	NICAM DUAL-I→
		NICAM DUAL-I/II	NICAM DUAL-II→
			Mono

		Regular broadcast	Mono
		(Standard audio)	Mono
		(Standard audio)
	A2
	A2	Bilingual or DUAL-I/II	DUAL-I↔ DUAL-II
	Stereo	Bilingual or DUAL-I/II	DUAL-I↔ DUAL-II
	Stereo

		Stereo	Stereo ↔ Mono
		Stereo	(Forced mono)
			(Forced mono)

➣◆ If the receiving conditions deteriorate, listening will be easier if the mode is set to the Mono.

◆If the stereo signal is weak and an automatic switching occurs, then switch to the Mono.

◆When receiving a mono sound in the AV mode, connect to the “AUDIO-L” input connector on the side of the television. If the mono sound comes out only from left speaker, press the DUAL I-IIbutton.

42

Image 42

Samsung 4240 manual Selecting the Sound Mode depending on the model

Contents

PDP-TELEVISION Cell Defect WarrantyScreen Image retention Height Power Cord Owner’s InstructionsSold Separately Contents Symbols Actual configuration on your PDP may be different Depending on your model Depending on your model For further details about connection, refer to pages 55~59 Infrared Remote Control Inserting the Batteries in the Remote Control Angle of the PDP can be up to 20 degrees left/right Installing the Display on the Wall Attachment Panel Wall Mount Bracket Plastic Hanger Connecting External Devices to the PDP Rear of the PDP Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Use the 3M/5M/7M cable supplied by Samsung Switching On and Off Mains lead is attached to the rear of your PDP Change channels and adjust the volume Becoming Familiar with the Remote ControlRemote control is used mainly to Display the on-screen menu system Setting Up Your Remote Control Plug & Play Feature To start the search, press the Enter button If you want to reset this feature Choosing Your Language Storing Channels Automatically See Storing ChannelsManually Auto PAL Secam or Auto NT3.58 NT4.43 PAL60BG DK I L Channel mode Skipping Unwanted Channels Skipping unwanted channels Sorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the Child Lock Activating the child lock Displaying Information Changing the Picture StandardDynamic Standard Movie Custom High Middle Low Custom Brightness, Sharpness Adjusting the Picture SettingsCustom Options available in PC, DVI Mode Contrast Colour Tone Cool2, Cool1, Normal, Warm1, Warm2 Adjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3 Setting the Picture PC Mode Preset to the PC mode by using the Source button Setting the Picture PC Mode Using the Fine Tune Colour System and Sound System settings are correctIf reception is weak, you can fine tune a channel manually Result Main menu is displayed Viewing the Channel Scan PictureFreezing the Current Picture Result Options available in the Channel group are Positioning and Sizing the screen using Zoom PC to DVI ModeSelecting the Picture Size Selecting the Film Mode DNIeTM Digital Natural Image engine Setting the Blue Screen Setting the Melody SoundSelect the option Off or On Table of PIP Settings Viewing the Picture In Picture PIP Picture Easy functions of remote controlButtons Feature Button after changing the sub Using the Digital NR Digital Noise Reduction Feature Changing the Sound Standard Standard Music Movie Speech Custom Adjusting the Sound Settings Adjusting the Volume Automatically Setting the TruSurround XT Selecting the Internal MuteStereo Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power Off Viewing an External Signal Source AV1, AV2, AV3, S-Video1,S-Video2,Component1Satellite STB, AV Receiver, DVD Receiver, Game Redirecting an Input to the External Output Teletext Feature Contents Displaying the Teletext Information Press the TTX/MIX button again Selecting Display Options To display Press Selecting a Teletext TeleWeb Feature Option Entering the bookmarked URL Using the TeleWeb Menu after Displaying the TeleWebBookmarking the current Opening the Home Easy Accessing the TeleWeb Service via the Remote Control TeleWeb Rear of the TV Connecting to the External DevicesInput/Output Specification Input Connecting to the S-Video Input Rear of the TV Side of the TV Connecting to the DVI Input Connecting to the PC Input Connecting to the Component Input Connecting Additional Speakers Connecting and Using the Home Theater System Connecting the Home Theater SystemTo Display the DVD Home Theater Installing the Speakers This speaker installation guide is for the 4240 Model How to Assemble the Speakers Wall Mount Bit colour Shown at left is a typical screen for Display dialog box Video Signal Dot x Line Vertical Horizontal NVidia chipset DVI Input Connector Scart Connector AV1/AV2/AV3PC Input Connector 15Pin Check the volume Power buttonCheck the picture contrast and brightness settings Normal picture but no sound Check the volume 019, 023 Programming the Remote Control for Other Components003, 024 Wamer amex NEC 040, 047, 050, 052, 060, 063, 065, 066, 067 After Sales Service