Communication, System Info | Samsung SCC-C7453N specs

setup

COMMUNICATION

You can set the RS-485 communications setting in regard of the camera.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 22)

1.Select <MAIN MENU>-<COMMUNICATION>.

2.Select each item and set appropriately.

PRIORITY : Set the priority by selecting <HW> or <SW>.

When selected <HW>, the protocol, baud rate and address settings will follow those settings of the adaptor switch.

PROTOCOL, BAUD RATE, ADDRESS : When selected <SW>, you can manually set the protocol, baud rate and address.

COMMUNICATION 

RS485
PRIORITY	HW
PROTOCOL	SAMSUNG
	HALF
BAUD RATE	9600
ADDRESS	0

SYSTEM INFO

You can check the system information.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 22)

1.Select <MAIN MENU>-<SYSTEM INFO>.

2.The current system information is displayed.

SYSTEM INFO 

TYPE	4_PTZ_NOR_N
PROTOCOL	SAMSUNG
ADDRESS	0
COMM. TYPE	HW, RS485, HALF
BAUD RATE	9600
SERIAL NO.	000000000000000
CAMERA VER.	v1.00_00000
ALARM VER.	v1.00_00000

48_ setup

00956B-NA_SCC-C7453N-ENG.indb 48

2009-08-13 오후 10:58:

Image 48

Samsung SCC-C7453N Communication, System Info, You can check the system information, Select Main MENU-SYSTEM Info

Contents

Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s Included At a Glance CameraFrame SET Installation & connection Optional Accessories for Installation English Precautions HousingPreparation Cable Installation Power BNC Cable Bush 24V Cable Housing MountPIN Bush Bush 22P Connector Housing Rack Housing Camera Screws Cover Dome Gasket DomeFrame SET Hook Protective Camera Tape Cover Initial Setup Camera Address SetupCommunication Protocol Setup Samsung Half Samsung Full Baud Rate Setup Setting RS-422A/RS-485 TerminationUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPS RS-422A/RS-485 Full Duplex Organization Same address in the network Connecting with Other device Connecting to a monitorMonitor Alarm Alarm OUT CONTROLLER/DVR Power Source To connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile DAY Mode NightBurst EXT Burst You can configure the general settings of the camera module Camera SETCamera ID  Location Specify the display position of the camera ID  Manual Adjust the iris level manually With this, you can adjust the AGC level of aIris AGC Motion DNRShutter SENS-UP You can specify a recording mode according to the scene FlickerlessXDR DAY/NIGHT Auto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Zoom Speed Display ZoomDisplay P/T Digital Zoom Sync AGC Color SUPReverse POSI/NEGA You can enable the motion detection and tracking functions When multiple motions continue arbitrarilyIntelligent Video Advanced Resolution Alarm OUTPrivacy Zone Display Preset Select the preset number Select Position and adjust PAN Auto Pan Setup Settings so define them again after the operationAuto SET You can set the Auto PAN, PATTERN, and Auto Play Position Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for Preset Zone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET  Auto SET Sets the pattern and scan Clock SET Other SET Factory Defaults PasswordOSD Color Proportional P/T Communication System InfoYou can check the system information Select Main MENU-SYSTEM Info Language You can set the language of the user interface Shortcut Keys Function Key Specifications Smart Dome CameraINT/LINE Lock PAN Tilt Product Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후