When desiring to see in the PIP screen | Samsung SDM-090P, SDM-160P

Digital Multiplexer

When desiring to see in the PIP screen

The PIP (picture in picture) screen may be seen using the “PIP” button on the FULL screen in the LIVE mode. The size of the PIP sub-screen is set in the “PIP SIZE” of the “2. MON OUT SET” on the program menu. The sub-screen is automatically and sequentially converted if pressing the “SEQUENCE” button.

➢Method to use

1.Press the “PIP” button.

2.Press the “SET”. In this case the LED of the “SET” button blinks and the border line blinks. Then, set the sub-screen of the PIP screen to a desired channel.

3.Press the “SET” button if completing the channel setting. In this case the LED of the “SET” button turns off.

4.Fix the position of the sub-screen using the “MOVE” button. The position of the sub-screen may be selected in 4 cases of right upper, left below, right upper, right below.

➢The “PIP” button does not operate in the following cases:

-In replay mode or TRIPLEX mode

-In division screen

-In automatic sequential conversion mode

-In zoom operation

-In setting program mode

-In displaying ALARM/LOSS LIST on screen

When desiring to see in the record screen

You can see the record output screen in the live mode using the “REC CHECK”.

When desiring to see output of VCR as it is

You can see the output screen of VCR using the “REC CHECK” button in the replay mode. This mode is useful when adjusting MENU of VCR.

➢The “REC CHECK ” button does not operate in the following cases:

-In zoom operation

-In setting program mode

-In displaying ALARM/LOSS LIST on screen

ENGLISH

4-5

Image 23

Samsung SDM-090P, SDM-160MP, SDM-160P When desiring to see in the PIP screen, When desiring to see in the record screen

Contents

Digital Multiplexer Important Safeguards Iii Contents Appendix B Checking Points in Trouble Introduction Introduction Name of parts and Function Move → Rear panel Physical & Environmental Preparing for the Installation Precautions when Installing Digital Multiplexer Unpacking Connecting to S-VHS VCR and S-VHS Monitor Connecting to Other DevicesConnecting to normal VCR and Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Ascii Remote Control by connecting to PC Spot OUT Control Remote Control using SSC-1000RS-485Monitor OUT Control @ Spot OUT Control Initial operation When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen Basic Method to use When desiring to see in the division screen When desiring to see in the Full screen When desiring to see automatic sequential conversion screen Full Mode 2TIMES Zoom Times Zoom When desiring to see the stop screenWhen desiring to see in the zoom screen When desiring to see output of VCR as it is When desiring to see in the PIP screenWhen desiring to see in the record screen Duty SET Reservation OFF Setting of Program MenuRecord setting of each camera REC OUT SET Type TLV END Time REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9REC Reservation Start Time PB Display ALL Spot OUT Cvbs PIP Size Setting of display modeSequence Loss Detect Loss Info Alarm Info Motion Info ALL Sequence Alarm S/W Time CH15 on Setting of title by channel DATE/TIME SET Display Type Title SETIjklmnopqrstuvwxyz Setting of motion Setting of alarm Motion OUT OFF ↔ on List Update OFF ↔ onXxxxx Sensitivity OFF ↔ LOW ↔ Medium ↔ High Baud Rate System settingPassword Change Password Check OFF Alarm Buzzer Loss Buzzer Summer Time +++++++++++++++++ + - - - - + Password Change Password Check NEW Password Confirm Recording Normal record modeTime Lapse record mode REC Duty Weight value REC Duty recordAlarm weight value record Reservation record Alarm signal standard Alarm occurrence conditionsAlarm release Alarm record Operation in motion detection Alarm/Loss list referenceOperation in video loss Image input Appendix a Specifications Outside Drawing Appendix B Checking points in trouble When record is not done