Samsung SSA-S2000/EXP specification

TO SPECIFY THE INPUT MODE FOR THE EXIT BUTTON

You can specify an operation for the Exit button when it switches from LOW (0V) to HIGH (5V).

1.Present the Master Card to the device.

2. Press Button 6 and Button 7 and Button	ENT .
• To release the setting, press the < 6 8	> buttons and press ENT .

t

Gj

X Y Z

\ ]

`

lzj W lu{

i

zzhTzYWWW

ADVANCED SETTING

	X	Y	Z
M	[	\	]
M	 The default is set to “switch from HIGH(5V) to LOW(0V)”.	_	`
	lzj	W	lu{
	i
			zzhTzYWWW

TO SPECIFY THE INPUT MODE FOR THE DOOR CONTACT SENSOR

You can specify an operation for the Door Contact Sensor when it switches from LOW (0V) to HIGH (5V).

1.Present the Master Card to the device.

2. Press Button 6 and Button 9 in sequence and press ENT .

•To release the setting, repeat Step 1 above, select the

< 7 0 > buttons and press ENT .

tGj

X Y Z

\ ]

`

lzj W lu{

i

zzhTzYWWW

M The default is set to “switch from HIGH(5V) to LOW(0V)”.

X Y Z

[\ ] _ `

lzj W lu{

i

zzhTzYWWW

English _ 37

Image 37

Samsung SSA-S2000/EXP To Specify the Input Mode for the Exit Button, To Specify the Input Mode for the Door Contact Sensor

Contents

Imagine the possibilities Standalone Rfid Access Controller Safety information Safety information This device may not cause harmful interference, Important Safety Instructions Contents To specify the input mode for the Door To specify the input mode for AUXTo specify the use of the tamper alarm Contact Sensor alarm Product introduction Features Quick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables Front View AT a Glance Cable Color Scheme Installation and external connection DC12V Cable Selection Connection Bypass Diode Connection Output Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened Initialization Wiegand Output SetupBrown line with white stripes TTL Output Chime Bell Output Hardware Forcible Initialization Forced Initialization with External Line Reader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup PIN only Reader Mode Setup RF + P/WPress Button 0 and Button Enabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton Sequence, and press ENT User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID  See the table below for your reference To Specify the Delayed Start Time in Secure Mode To Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact Sensor To Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled Device To SET or Release the Toggle Mode for the Door Relay To SET or Release the Quick ModeDefault is set to not used Buttons and press ENT To Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Duress TTL Output To Specify the Output Time if the Card is not Authenticated Enter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX 32 I/O time setup \ ` To Specify the TTL Output Operation Mode Advanced setting The default is set to switch from HIGH5V to LOW0V  The default is set to use the chime bell To Specify the Chime Bell Operation Time To Specify the Input Mode for AUX Advanced setting To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit Button To Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card User To Check the Output Specified for AUX Additional Features Initial Values Other informationThis product operates in the following initial values Function Codes Sense if AUX 1 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 2 switches from L to H Sense if AUX 2 switches from H to L Troubleshooting Troubleshooting √ RF Only Service center √ Enter the command to delete the user 14 + ENTEInstall and use the product as usual Check the operation status of the product Unregistered numbers in 5 consecutive times default Using the keypadUser cards to the factory default CIf SSA-S2000 responds when you press the Exit button Disconnection or short-circuit Irrelevant data is transferredSSA-S2000 Consult with a qualiﬁed technician Weight 220g Product SpecificationsProduct speciﬁcations 87.0 x 109.0 x Correct disposal of batteries in this product