Reader Mode Setup RF/PIN Combination Mode | Samsung SSA-S2000/EXP

reader mode setup

READER MODE SETUP (RF/PIN COMBINATION MODE)

No Master Card or Master PIN is ever registered.

If you remember the Master Card or the Master PIN was registered, initialize the product and try again.

1.When you turn on the product, all of the 3 LED indicators will ﬂash with a beep.

•No flashing of the 3 indicators denotes that the reader mode is already specified.

2. Press Button 0 and Button 5 in sequence and press ENT .

3.Present a card that you want to register as the Master Card to the device. When the Master Card is registered, only the red LED indicator flashes.

4.Present cards or PIN numbers (4-6 digits) to register with the device one after another, and the device will register them with a beep. If you don’t want

to register the cards right now, simply jump to Step 5 above without through Step 4 above.

5.Present the registered Master Card to the product once again.

6.The device enters Standby mode with only the orange LED indicator flashing.

X Y Z

[\ ] ^ _ `

lzj W lu{

i

zzhTzYWWW

X	Y	Z	Î	X	Y	Z	or
		]	Î	[	\	]
		]		[	\	]
		`		^	_	`
tGj	W	lu{		lzj	W	lu{
lzj	W	lu{			W
i				i
		zzhTzYWWW				zzhTzYWWW

X	Y	Z	Î
[	\	]	Î
^	_	`
lzj	W	lu{
i
		zzhTzYWWW

X Y Z

]

t
lzj	W	lu{
Gj	W
i
		zzhTzYWWW

ENABLING KEYPAD INPUT FOR THE CARD NUMBER

Ensure that you must have registered the Master Card.

1.Present the Master Card to the device.

2. Press Button	7 and Button 3 in sequence and press ENT .
• Repeat Step 1 above to release the specified mode, press Button 7 and
Button 4	in sequence, and press ENT .

tGj

X Y Z

\ ]

`

lzj W lu{

i

zzhTzYWWW

M You can set the device to allow you to control the door by entering the 8 digit card number using the keypad.

The default is “Keypad Input Disabled”.

X Y Z

[\ ] ^ _ `

lzj W lu{

i

zzhTzYWWW

20_ reader mode setup

Image 20

Samsung SSA-S2000/EXP manual Reader Mode Setup RF/PIN Combination Mode, Enabling Keypad Input for the Card Number

Contents

Standalone Rfid Access Controller Imagine the possibilities Safety information Safety information Important Safety Instructions This device may not cause harmful interference, Contents To specify the input mode for AUX To specify the input mode for the DoorTo specify the use of the tamper alarm Contact Sensor alarm Features Product introduction Master Card Cables WHAT’S IncludedQuick Guide Rings Diodes UF4004, 1N4001~4007 AT a Glance Front View Cable Color Scheme Installation and external connection Cable Selection DC12V Bypass Diode Connection Connection Output Connection External Reader Connection If you press the Exit button, the door will be opened InitializationBasic Operations Wiegand Output Setup InitializationBrown line with white stripes TTL Output Chime Bell Output Forced Initialization with External Line Hardware Forcible Initialization No Master Card or Master PIN is ever registered Reader mode setupReader Mode Setup RF only Press Button 0 and Button Reader Mode Setup RF + P/WReader Mode Setup PIN only Button Sequence, and press ENT Reader Mode Setup RF/PIN Combination ModeEnabling Keypad Input for the Card Number Registering Cards in a Combination of RF and P/W Modes To Register Cards in RF only ModeUser management Master PIN To Register Cards in PIN ModeRegistering Cards in RF Card / PIN Combination Mode To Delete a Registered Card or PIN Number To Specify the Retry Count for AN Unregistered ID Basic setupDuress Alarm To Specify the Delayed Start Time in Secure Mode  See the table below for your reference To Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad Input To Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry Door To SET or Release the Quick Mode To SET or Release the Toggle Mode for the Door RelayDefault is set to not used Buttons and press ENT You can specify from 10 to Time setupTo Specify the Output Time if the Card is Authenticated To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL Output To Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT 32 I/O time setup \ ` Advanced setting To Specify the TTL Output Operation Mode The default is set to switch from HIGH5V to LOW0V  The default is set to use the chime bell To Specify the Input Mode for AUX To Specify the Chime Bell Operation Time Advanced setting To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact Sensor Mute Additional featuresTo Specify the USE of the Tamper Alarm To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for AUX Additional Features This product operates in the following initial values Other informationInitial Values Function Codes Sense if AUX 1 switches from L to H Sense if AUX 1 switches from H to LSense if AUX 2 switches from L to H Sense if AUX 2 switches from H to L Troubleshooting Troubleshooting √ RF Only √ Enter the command to delete the user 14 + ENT Service centerEInstall and use the product as usual Check the operation status of the product Using the keypad Unregistered numbers in 5 consecutive times defaultUser cards to the factory default CIf SSA-S2000 responds when you press the Exit button Irrelevant data is transferred Disconnection or short-circuitSSA-S2000 Consult with a qualiﬁed technician Product Specifications Weight 220gProduct speciﬁcations 87.0 x 109.0 x Correct disposal of batteries in this product