Reader Mode Setup RF + P/W | Samsung SSA-S2000/EXP guide

READER MODE SETUP (RF + P/W)

No Master Card or Master PIN is ever registered.

If you remember the Master Card or the Master PIN was registered, initialize the product and try again.

1.When you turn on the product, all of the 3 LED indicators will ﬂash with a beep.

•No flashing of the 3 indicators denotes that the reader mode is already specified.

2. Press Button 0 and Button 2 in sequence and press ENT .

3.Present a card that you want to register as the Master Card to the device. When the Master Card is registered, only the red LED indicator flashes.

4.Present a card to the device, enter the 4-6 digit password and press ENT .

If you don’t want to register the cards right now, simply jump to Step 5 above without through Step 4 above.

5.Present the registered Master Card to the product once again.

6.The device enters Standby mode with only the orange LED indicator flashing.

X Y Z

[\ ] ^ _ `

lzj W lu{

i

zzhTzYWWW

READER MODE SETUP

X Y Z

Î

X Y Z

Î

X Y Z

Î

X Y Z

[

]

[

\

]

[

\

]

t

\

]

`

^

_

`

^

_

`

`

tGj

W

lu{

lzj

W

lu{

lzj

W

lu{

lzj W

lu{

lzj

Gj

i

i

i

i

zzhTzYWWW

zzhTzYWWW

zzhTzYWWW

zzhTzYWWW

READER MODE SETUP (PIN ONLY)

No Master Card or Master PIN is ever registered.

If you remember the Master Card or the Master PIN was registered, initialize the product and try again.

1.When you turn on the product, all of the 3 LED indicators will ﬂash with a beep.

•No flashing of the 3 indicators denotes that the reader mode is already specified.

X Y Z

[\ ] ^ _ `

lzj W lu{

2. Press Button 0 and Button 3	in sequence and press	ENT .	i
			zzhTzYWWW

When the mode is speciﬁed, only the green LED indicator ﬂashes.

3.Enter the 4-6 digit Master PIN number and press ENT .

When the Master PIN is registered, only the red LED indicator flashes.

4.Enter a PIN number to register (4-6 digits) and press ENT .

Repeat the step above if you want to register PIN numbers with the device in sequence.

If you don’t want to register the PIN number right now, simply jump to Step 5 above without through Step 4 above.

5.Enter the 4-6 digit Master PIN number again and press ENT .

6.The device enters Standby mode with only the orange LED indicator flashing.

English _ 19

Image 19

Samsung SSA-S2000/EXP manual Reader Mode Setup RF + P/W, Reader Mode Setup PIN only, Press Button 0 and Button

Contents

Imagine the possibilities Standalone Rfid Access Controller Safety information Safety information This device may not cause harmful interference, Important Safety Instructions Contents Contact Sensor alarm To specify the input mode for AUXTo specify the input mode for the Door To specify the use of the tamper alarm Product introduction Features Quick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables Front View AT a Glance Cable Color Scheme Installation and external connection DC12V Cable Selection Connection Bypass Diode Connection Output Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened TTL Output Chime Bell Output Wiegand Output SetupInitialization Brown line with white stripes Hardware Forcible Initialization Forced Initialization with External Line Reader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup PIN only Reader Mode Setup RF + P/WPress Button 0 and Button Enabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton Sequence, and press ENT User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID  See the table below for your reference To Specify the Delayed Start Time in Secure Mode To Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact Sensor To Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled Device Buttons and press ENT To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Default is set to not used To Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Duress TTL Output To Specify the Output Time if the Card is not Authenticated Enter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX 32 I/O time setup \ `  The default is set to use the chime bell Advanced settingTo Specify the TTL Output Operation Mode  The default is set to switch from HIGH5V to LOW0V To Specify the Chime Bell Operation Time To Specify the Input Mode for AUX Advanced setting To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit Button To Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card User To Check the Output Specified for AUX Additional Features Initial Values Other informationThis product operates in the following initial values Function Codes Sense if AUX 2 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from L to H Troubleshooting Troubleshooting √ RF Only Check the operation status of the product √ Enter the command to delete the user 14 + ENTService center EInstall and use the product as usual CIf SSA-S2000 responds when you press the Exit button Using the keypadUnregistered numbers in 5 consecutive times default User cards to the factory default Consult with a qualiﬁed technician Irrelevant data is transferredDisconnection or short-circuit SSA-S2000 87.0 x 109.0 x Product SpecificationsWeight 220g Product speciﬁcations Correct disposal of batteries in this product