e00_VDH_M814.book Page 11 Thursday, October 28, 2004 9:59 AM

INSTALLATION AND CONNECTIONS

Connecting the power

 

When you have finished making all the other

 

connections, insert the power plug into the

INTRODUCTION

wall outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

There is no power switch. The display indicators flash, and

 

 

after a few moments, the monitor screen displays the

 

camera image.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

LAN

 

 

 

1

 

 

 

 

2 VIDEO 3

4

 

3

IN

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

4

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

2

3

4

 

 

ALL

OUT

 

 

 

 

 

 

 

 

 

 

OUT

 

 

RESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MONITOR OUT

 

 

 

 

 

 

 

 

 

 

AC IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-485

 

 

 

 

 

 

 

 

 

 

 

 

 

TV SYSTEM TERMINATE

 

 

 

 

 

 

 

 

 

 

 

 

 

NTSC

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

PAL

OFF MIC IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16 17 18 19

Power cable

zWhen turning the power ON for the first time “PLEASE SET THE CLOCK” is flashed on the monitor screen. Follow the steps on page 34 to set the clock.

zIf the clock is already set

The operation display area is displayed.

Operation

HI A

display area

05 - 10 - 04 08 : 30 : 35 AL 000 15

zIf a problem occurs when connecting the power or during operation, the POWER indicator flashes as follows to indicate the type of problem. Contact a Sanyo Authorized Service Center if this happens.

POWER indicator

Problem

 

 

 

A problem has been found on

 

the hard disk. The hard disk

Flashes 4 times

must be replaced or formatted.

If you need to save videos

per second

stored on the hard disk,

 

 

contact a Sanyo Authorized

 

Service Center.

 

 

Flashes 1 time per

There is a problem with the

second

fan.

 

 

11

zAfter disconnecting the power cable, do not move the unit or subject it to vibration for at least 30 seconds. The disk in the hard disk drive briefly keeps spinning after the power is disconnected due to inertia. During this time the head is unstable, and the disk is more sensitive to shocks and vibrations than usual, so avoid even the lightest shocks.

Securing the power cord

Secure the power cord to the holder using the supplied power cord tie as shown in the illustration.

Power cord tie

System controller connections

A single system controller (sold separately) allows you to set up multiple digital video recorders at the same time. ( P.66)

Remote control connections

A remote control can be used to perform the operations of the buttons on the front panel. To perform remote control operations, you must construct your own remote control.

( P.67)

Alarm sensor connections

Commercially available alarm sensors (normal open, low-level at detection) can be connected to the ALARM IN (1 to 4) terminals on the rear panel. ( P.67)

Series recording connections

When connecting this unit to additional digital video recorders, recording continues automatically on the next recorder when the hard disk of the first recorder is full.

( P.67)