OUTPUT TERMINALS

SW OUT Terminal

When recording, a pulse signal is output at the SW OUT
terminal.
This terminal is usually connected to the switch input (SW
IN) of devices like a camera switcher unit, or a quad
compressor.
SW OUT Terminal Output Setting
1Press the MENU button until the (SET UP 4) menu is
displayed.
ø
The FIELD (or FRAME) setting is flashing.
@@@@@@@@<SET@UP@4>
öSW@OUT
@@FIELD@@@@@@@@@01
@@TIMING@@@@@@@@FIELD
@@2H@@@@@@@@@@@@Y
öTHREAD@CHECK@@@Y
öVIDEO@LOSS@@@@@N
öREC@SPEED@@@@@@N
ö1@SHOT@SET
@@FIELD@@@@@@@@@1
@@INTERVAL@@@@@@1M
NOTE:
œIf “TIMING” is set to FRAME (see step 4),
“FRAME” will be indicated instead of “FIELD”.
2Turn the SHUTTLE ring, to set the desired pulse
signal interval.
Available settings are:
FIELD. . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 field
FRAME . . . . 01, 02, 03, 04, 05, 10, 30 or 60 frame
3Turn the JOG dial clockwise until the “TIMING”
setting is flashing.
4Turn the SHUTTLE ring, to set “FIELD” or “FRAME”.
FIELD. . . . . . 1 pulse is output after each set
number of fields.
FRAME . . . . 1 pulse is output after each set
number of frames.
5Turn the JOG dial clockwise until the “2H” setting is
flashing.
6Turn the SHUTTLE ring, to set the desired “2H” mode.
Y . . . . . . . . . When recording in 2-hour mode, a
pulse signal is output.
N . . . . . . . . . When recording in 2-hour mode, a
pulse signal is not output.
7Press the SEARCH/AUDIO ON button to save the
settings.

SERIES OUT/NON REC OUT terminal

setting

The output at the SERIES OUT/NON REC OUT terminal
can be set.
1Press the MENU button until the (SET UP 1) menu is
displayed.
@@@@@@@<SET@UP@1>
öDAYLIGHT@SET@@@@@USE
@@@@@@@@WEEK@MONTH@TIME
@ON@@@1ST-SUN@@04@02:00
@OFF@@LST-SUN@@10@02:00
öOUTPUT@@@@@@@@SERIES
öCLOCK@SET
@10-15-99@FRI@@15:20:00
öREMOTE@@@@@@@@EJECT
öLANGUAGE-LANGUE-IDIOMA
@@@ENGLISH
2Turn the JOG dial, until the “OUTPUT” setting is
flashing.
3Turn the SHUTTLE ring, to select the desired output
mode.
SERIES . . . . If during series recording, the
counter reading reaches
1H57M00S or the tape reaches the
end, a LOW signal (0 V) is output.
The LOW (0 V) signal is output for
about 70 seconds after the end of
the tape is reached.
NON REC . . If during recording the VCR enters
a mode other than recording (i.e.
recording pause, stop mode, etc.),
a LOW signal (0 V) is output. If
recording is resumed, then a HIGH
signal (5 V) is output.
If in the (SET UP 2) menu, in the
BUZZER section, WARNING is set
to “Y”, a buzzer will be heard while
the VCR is in non recording mode.
The buzzer will stop if the STOP
button is pressed (the output signal
will remain LOW (0 V)).
4Press the SEARCH/AUDIO ON button to save the
setting.
5V (H)
0V (L)
(Output impedance: 5.7 kΩ)
FIELD: 16.7 msec.
FRAME: 5 msec.
RC4Q/U (TLS-9960 GB) Mon. Aug., 23/1999
English 39