Sanyo VSP-9000 bSub Screen Operation

Hard Disk Digital Recorder (DVR) Operation

Recording stop button

REC STOP The recording stop screen is displayed on the menu display.

Press esc to continue recording, or press enter to stop recording.

esc

R E C S T O P	O K ?
N O :	e s c
O K :	e n t e r

enter

Timer record button

TIMER

ON/OFF Press during recording to enter timer record standby. The timer will record at the set time. Press again to cancel.

Plus display button

While monitoring the main monitor multiple display screen, image from one camera is displayed larger. The display panes differ based on the number of camera input terminals. Press again to cancel.

bSub Screen Operation

Main monitor button (*)

MAIN

MONITOR Press to operate the main monitor.

C A M

2 D V R

1

Multiple display button

MON2

Monitor 2 button (*)

Press to operate monitor 2.

Search button

The main monitor displays a nine-pane or sixteen-pane screen. The display panes differ based on the number of camera input terminals on the hard disk digital recorder.

SEARCH

FR/FI Press in any search operation menu, whether during recording or while stopped.

Pause button

STILL Press this during playback. A still picture is displayed. Press it again to return to playback.

Playback stop button

PLAY STOP Press this during playback to stop playback.

Clock setting button

CLOCK

ADJUST Press this to set the minutes and seconds to “00”.

esc

ZOOM

MENU

Cursor buttons

Use in place of the jog shuttle when making menu selections. The cursor will move.

Zoom button

Press the zoom button during playback on a single screen, or while monitoring live image.

A zoom frame is displayed around the center of the screen.

Press again to cancel the zoom.

Menu reset button

C L O C K A D J U S T O K ?

N O : e s c

RESET This restores the default menu settings.

O K : e n t e r

enter

CHANNEL

Channel button

The camera channel can be selected during a pause.

C A M

1 D V R

1

(*): The Sub-menu screen appears.

English

Operation 34

Contents

System Controller Introduction Preparation Operation System Setup Software CAUTION WARNING: CAUTION: Page Safety Cautions Safety Cautions (Continued) bMenu Display Always Observe These Rules for Proper Use Page Front Back Rear Page 1Status of selected equipment (UNDER SELECTION) 2Communication status for video equipment or camera (TELEMETRY) 3Communication status for video equipment (VIDEO) A When connected to video communication terminal (VIDEO) P15 BWhen connected to video communication terminal (VIDEO) P18 P21 Sample System Connection DWhen connected to video communication terminal (VIDEO) and camera communication terminal (TELEMETRY B) P24 P27 AWhen connected to video communication terminal (VIDEO) bConnecting communication conversion connectors bMaking Connections 2Terminate Setup bCommunication Setup 1Press the SYSTEM button, then press the button Connection and Communication Setup 1 (continued) 3Press the esc button 4Press the button, select “2–TELEMETRY”,then press the ent button 5Press the esc button Page Connection and Communication Setup 2 (continued) Page Page Page Page Page Connection and Communication Setup 4 (continued) Page Page Page Connection and Communication Setup 5 (continued) bNumber of Connected Units bTerminate settings Communication Lines and Number of Connected Units (Continued) 1Press the ADDRESS ? DVR button 2Use the ten-keypad to enter the recorder address (Example: 1) 3Press the enter button Hard Disk Digital Recorder (DVR) Operation (Continued) 4Press 6Press the enter button 7Switch between the sub screen ( TO SUB button) and the bSub Screen Operation Page 1Press the MUX button 2Press the ADDRESS ? MUX button 3Use the ten-keypad to enter the multiplexer address (Example: 1), then press the enter button Multiplexer (MUX) operation (Continued) 1Press the ADDRESS ? button 2Use the ten-keypad to enter the camera input channel 3Basic camera operation Press a button inside the on the Menu screen 4Press the detailed camera operation button TO SUB Dome Camera/Zoom Camera Operation (Continued) Dome Camera/Zoom Camera Operation Page 2Press the press the ent button 4Press the button bSelect a communication item (COMMUNICATIONS) bUnit Address Setup 2Press a number button (example: 3), then press the enter button 4 5 6 del esc 1Press the button to select “Keyboard Add”, then press Communication Setup (Continued) 1Connect test cables to each camera communication terminal (TELEMETRY A and B) on the rear panel 2Check the results displayed on the menu display 3When the test is complete, press the esc button to return to the Menu screen b Select a Control Item (ACCEPTED VALUES) Control Setup Control Setup (Continued) Page Password Setup (PASSWORD) (Continued) bAT SWITCHING ON (Power ON password) 1Press the button or button to select “AT SWITCHING ON”, then press the ent button 2Press number buttons to enter the password, (example: Page Setup (CONFIGURATION) (Continued) bInitialize (RESTORE BASIS VALUES) 1Press the button or button to select “RESTORE BASIS VALUES”, then press the ent button Setup (CONFIGURATION) 3Press the ent button 2Press the button or button to switch the joystick setting position bJoystick Setup (JOYSTICK) b Touch screen adjustment 3Press the enter (TOUCH SCREEN SETTING) button or button to select “TOUCH 7Press the SAVEbutton bTouch Screen Initialization and Reset 1Remove wiring and power cables for all equipment connected to this unit 2Turn dipswitch (SW1) ON 5After initializing, operate the joystick as shown in the drawing to perform touch screen adjustment bTouch screen test (TOUCH TEST) 1Press the button or button to select “TOUCH 2 Software Configuration 2 Connection and Software Installation 2 System Setup (Setup) 2 Language Setup (Language) 2 Graphics Environment Setup (Maps) System Setup (Setup) P61 Language Setup (Language) P68 Graphics Environment Setup (Maps) bInstall the Software 1Insert the provided CD-ROMin the CD-ROMdrive on the PC open it, and click SETUP.EXE 3Connect the PC connection terminal (COM) on the rear 2Follow the instructions on the screen to install the software 1Menu 2Toolbar 3Tabs AGeneral (General Settings) 1From the “File” menu, select “New” 2Click the [General] tab 3Make the various settings. (P63) 4Make the various selections System Setup (Setup) (Continued) BCameras (Camera communication setup) 1Click the [Cameras] tab 2Set camera lines using the various buttons 3Select a camera for communication settings double-clickit, and click the Changing the Camera Address Number CMonitor/Local Mux (Valid/Invalid setup for hard disk digital recorder with multiplexer) 1Click the [Monitor/Local Mux] tab 2Set the video equipment output using the various DEnabling (stopping or starting settings) 1Click the [Enabling] tab 2Check the functions to turn ON 3Make the various selections Page Language Setup (Language) (Continued) bCreating Two Different English Tabs 1From the “Text management” menu, select “Receive from keyboard” 3Select Tab 2 (English) in Window A, and Tab 7 in 7Use the same procedure to change other words or change them into symbols, creating tabs with different English wording 8From the “Text management” menu, select “Send to Page bDisplay Telephone Number on Opening Screen 1From the “Project” menu, select “New” 3From the “Project” menu, select “Send to keyboard” 2Click the “Service” tab, click “ ”, and select the image file to read Page 1Map Display 2Map Selection 3Map selection button 4Joystick Function Selection 6Info tab (Allocation Setup Screen) (1) (2) (3) (1) Matrix/Mux-Dvr Page Page Page Page Page bChanging the Opening screen to “SANYO” 3Pastes the selected “SANYO” logo onto the opening screen 4From the “Project” menu, select “Send to keyboard” 2Click the “ ” icon, and select the image file to read bCreate a map using the graphics tool and display on opening screen 2From the “Images” menu, select “Change image” 3Click to save settings General Tools Saving settings on PC 2Color/Background Tools 3Drawing Tools bBasic Graphics 4Text input area 1Select the color to use 2Draw lines bOuter Dimensions (Units: mm) bCommunications Chart Appendix (Continued) Appendix bMessage Chart bSpecial Code Chart Page Page Page Page Page SANYO Electric Co., Ltd