Rotating Blades

Section 4

4.7 Hillside Operation

WARNING

DO NOT operate on steep slopes.To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. Under no circumstances should the machine be operated on slopes greater than 15 degrees. See Figure 2-4, Page 7 to help determine approximate slope of area to be mowed. ALWAYS FOLLOW OSHA APPROVED OPERATION.

1.This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Wet grass reduces traction and steering control. The Roll-Over Protection System is standard equipment for this machine. See Section 2.5, page 6 of this manual for further details.

4.9 After Operation

1.Wash the entire mower after each use. Do not use high pressure spray or direct the spray onto electrical components.

- IMPORTANT -

Do not wash a hot or running engine. Cold water will damage the engine. Use compressed air to clean the engine if it is hot.

2.Keep the entire mower clean to inhibit serious heat damage to the engine or hydraulic oil circuit.

3.Check the drive belts for proper alignment and any signs of wear. Correct and adjust if necessary.

Danger

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

2.Stay two cut widths away from slopes, drop offs, ditches and retaining walls.

3.To prevent tipping or loss of control, do not start or stop suddenly, avoid unnecessary turns and travel at reduced speed. If tires loose traction, disengage blades and proceed slowly off the slope.

4.Avoid sudden starts when mowing uphill. Sudden starts may cause the machine to tip backwards.

5.Loss of traction may occur when traveling down hill. Weight transfers to the front of the machine and may cause the drive wheels to slip causing loss of braking or steering.

6.Keep tires properly inflated.

4.8 Parking The Mower

1.Park the machine on a flat, level surface only. Do not park the machine on an incline.

2.Place the steering control levers in the neutral position.

3.Disengage the cutter blades.

4.Slow the engine to idle speed.

5.Engage the parking brake.

6.Turn the ignition key to the OFF position and remove the key.

4.After the mower has cooled down, fill the fuel tank with fresh, clean fuel at the end of every day of operation. See Engine Owner's Manual for proper octane requirements.

5.Check the tire pressure. Adjust pressure if necessary.

4.10 Removing Clogged Material

Danger

NEVER PUTYOUR HANDS INTOTHE DISCHARGE CHUTE FOR ANY REASON!

Shut off the engine and remove the key and only then use a stick or similar object to remove material if clogging has occurred.

1.If the discharge chute becomes clogged, shut off the engine and remove the ignition key. Using a stick or similar item, dislodge the clogged material. Then resume normal mowing.

STT-35BVAC, STT61V-29DFI-LE, STT61V-35BVAC, STT61V-29DFI, STT-29DFI specifications

Scag Power Equipment is renowned for its high-quality lawn care machinery, and among its range of products, the STT series stands out, particularly the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, and STT-35BVAC models. These zero-turn mowers are designed to deliver exceptional performance, durability, and efficiency, catering to both commercial landscapers and homeowners alike.

The STT-29DFI offers an impressive 29 horsepower, powered by a state-of-the-art EFI engine. This model boasts an advanced deck design, featuring a robust 61-inch cutting width that ensures a clean and even cut. The mower's zero-turn capability allows for enhanced maneuverability, making it easier to navigate around obstacles and achieve a professional finish.

In comparison, the STT61V-35BVAC takes power to the next level with a 35 horsepower engine. This model is perfect for tackling larger areas and more challenging terrains. The vacuum-assisted cutting system effectively collects clippings, reducing cleanup time after mowing. The heavy-duty, reinforced steel frame ensures long-lasting durability, while the comfortable operator seat and control system enhance user experience.

The STT61V-29DFI is another remarkable addition to this lineup, featuring a 29 horsepower engine equipped with EFI technology. This model focuses on fuel efficiency, allowing operators to maximize output while minimizing fuel consumption. With its 61-inch cutting deck, it provides an excellent balance between power and precision, ideal for both commercial and residential use.

For those looking for a more specialized option, the STT61V-29DFI-LE includes enhancements aimed at professional landscapers, such as a premium seat suspension system for extended comfort during long operating hours. This model also features a customizable control panel, making it easier for operators to tailor settings to their specific needs.

Lastly, the STT-35BVAC integrates a robust 35 horsepower engine, along with advanced features that promote efficiency and productivity. This model's design prioritizes user-friendly operation, with intuitive controls and easy access to maintenance points. The vacuum system further enhances its capabilities by collecting grass clippings and debris as you mow, ensuring a tidy lawn at all times.

In summary, Scag Power Equipment's STT series is characterized by powerful engine options, advanced cutting technologies, and a commitment to durability and operator comfort. Whether you choose the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, or STT-35BVAC, you can expect a mower that stands up to the demands of any lawn care task.

Scag Power Equipment STT61V-29DFI-LE manual Rotating Blades, Hillside Operation, After Operation

Models: STT-35BVAC STT61V-29DFI-LE STT61V-35BVAC STT61V-29DFI STT-29DFI