Initial Run-In Procedures | Scag Power Equipment STT61V-29DFI

Section 4

4.3 Initial Run-In Procedures

First Day of Use or Approximately 20 Hours

1.Check all belts for proper alignment and wear at 2, 4 and 8 hours.

2.Change the engine oil and oil filter after the first 20 hours of operation. (See Section 7.4.)

3.Check hydraulic oil level in reservoir. (See Section 7.3.)

4.Check for loose hardware. Tighten as needed.

5.Check interlock system for proper operation. (See Section 4.2.)

6.Check tire pressure. Adjust pressure if necessary. (See Section 7.10.)

4.4 Starting The Engine

CAUTION

DO NOT USE STARTING FLUIDS. Use of starting fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition that could result in engine damage and/or personal injury.

1.Be sure the fuel shutoff valve, located behind the operator's seat, is fully open. (See Section 7.5.)

2.Secure the ROPS in the upright and locked position.

3.Sit in the operator’s seat, fasten seat belt and place the steering control levers in the neutral position.

4.Engage the parking brake.

5.Place the PTO switch in the disengaged position.

6.If the engine is cold, choke the engine as needed.

7.Move the engine throttle control to about half engine speed.

8.Turn the ignition key to the START position and release the key as soon as the engine starts. Do not hold the key in the START position for more than 15 seconds at a time. Allow at least 60 seconds between each cranking attempt to prevent overheating of the starter motor. Prolonged cranking can damage the starter motor and shorten battery life.

9. Allow engine to warm before operating the mower.

4.5 Ground Travel And Steering

- IMPORTANT -

If you are not familiar with the operation of a machine with lever steering and/or hydrostatic transmissions, the steering and ground speed operations should be learned and practiced in an open area, away from buildings, fences, or obstructions.

Learn the operation on flat ground before operating on slopes.

Start practicing with a slow engine speed and slow forward travel.

Learn to feather the steering controls to obtain a smooth operating action.

Practice operating the mower until you are comfortable with the controls before proceeding to mow.

Forward Travel

To travel forward with the mower, disengage the parking brake, pull levers inward out of the neutral lock position and slowly push the steering control levers forward an equal distance. The further the steering control levers are pushed forward the greater the forward speed will be. To increase the speed, push the steering control levers further forward and to decrease the speed, pull the steering control levers back.

To stop the forward travel, pull the steering control levers back to the neutral position.

To steer the mower left while traveling forward, pull the left steering lever back. The further the lever is pulled back, the quicker the mower will turn left.

To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right.

- NOTE -

Smooth operation of the steering levers will produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

STT-35BVAC, STT61V-29DFI-LE, STT61V-35BVAC, STT61V-29DFI, STT-29DFI specifications

Scag Power Equipment is renowned for its high-quality lawn care machinery, and among its range of products, the STT series stands out, particularly the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, and STT-35BVAC models. These zero-turn mowers are designed to deliver exceptional performance, durability, and efficiency, catering to both commercial landscapers and homeowners alike.

The STT-29DFI offers an impressive 29 horsepower, powered by a state-of-the-art EFI engine. This model boasts an advanced deck design, featuring a robust 61-inch cutting width that ensures a clean and even cut. The mower's zero-turn capability allows for enhanced maneuverability, making it easier to navigate around obstacles and achieve a professional finish.

In comparison, the STT61V-35BVAC takes power to the next level with a 35 horsepower engine. This model is perfect for tackling larger areas and more challenging terrains. The vacuum-assisted cutting system effectively collects clippings, reducing cleanup time after mowing. The heavy-duty, reinforced steel frame ensures long-lasting durability, while the comfortable operator seat and control system enhance user experience.

The STT61V-29DFI is another remarkable addition to this lineup, featuring a 29 horsepower engine equipped with EFI technology. This model focuses on fuel efficiency, allowing operators to maximize output while minimizing fuel consumption. With its 61-inch cutting deck, it provides an excellent balance between power and precision, ideal for both commercial and residential use.

For those looking for a more specialized option, the STT61V-29DFI-LE includes enhancements aimed at professional landscapers, such as a premium seat suspension system for extended comfort during long operating hours. This model also features a customizable control panel, making it easier for operators to tailor settings to their specific needs.

Lastly, the STT-35BVAC integrates a robust 35 horsepower engine, along with advanced features that promote efficiency and productivity. This model's design prioritizes user-friendly operation, with intuitive controls and easy access to maintenance points. The vacuum system further enhances its capabilities by collecting grass clippings and debris as you mow, ensuring a tidy lawn at all times.

In summary, Scag Power Equipment's STT series is characterized by powerful engine options, advanced cutting technologies, and a commitment to durability and operator comfort. Whether you choose the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, or STT-35BVAC, you can expect a mower that stands up to the demands of any lawn care task.

Scag Power Equipment STT61V-29DFI Initial Run-In Procedures, Starting The Engine, Forward Travel

Models: STT-35BVAC STT61V-29DFI-LE STT61V-35BVAC STT61V-29DFI STT-29DFI