if anypartis missing,bent,orbrokeninanyway,oranyelectricalpartdoesn'tworkproperly,turnthesawoff andunplugthesaw.REPLACEdamaged,miss-ing,orfailedpartsbeforeusingthe sawagain.MAINTAINTOOLSWITHCARE.Keepthesawcleanforbestandsafestperformance.REMOVEADJUSTINGKEYSAND WRENCHESfromtoolbeforeturningiton.
To avoid injury from jams, slips or thrown pieces:
•Choose the right size and style blade for the
material and thetype ofcutting you plan to do.
• USE ONLY RECOMMENDED ACCESSORIES.
(See page 19). Consult this owner's manual for
recommended accessories. Follow the instruc-
tions that come with the accessories. The use of
improper accessories may cause risk of injury to
persons.
• Make sure the blade teeth point downward,
toward the table.
• Make sure the blade guides and thrust bearings
are properly adjusted.
• Make sure the blade tension is properly adjusted.
• Make sure the table lock knob is tight and no
parts have excessive play.
• To avoid accidental blade contact, minimize
blade breakage and provide maximum blade
support, always adjust the upper blade guide and
blade guard tojust clear the workpiece.
• KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents. Floor must not be
slippery.
To avoid burns or other fire damage, never use the
saw near flammable liquids, vapors orgases.

Plan ahead to protect your eyes,

hands, face, ears.

KNOW YOUR SAW. Read and understand the
owner's manual and labels affixed to the tool. Learn
its application and limitations as well as the specific
potential hazards peculiar to this tool.
To avoid injury from accidental contact with moving
parts, don't do layout, assembly, orsetup work on the
saw while any parts are moving.
AVOID ACCIDENTAL STARTING. Make sure switch
is pushed "OFF" before plugging saw into a power
outlet.
Plan your work.
• USE THE RIGHT TOOL. Don't force tool or
attachment to do a job itwas notdesigned to do.
•Use this band saw to cut wood, wood like prod-
ucts, plastics, non-ferrous and ferrous metals
(ferrous metals 1/16 inch thick or less).

Dress for safety•

WEAR YOUR
CAUTION: This saw is designed for cutting fer-
rous metals like iron or steel and non-ferrous met-
als (brass, copper and aluminum, etc.). Metal
shavings can react with wood dust and start a fire.
To avoid this:
• Disconnect any type of dust collecting hose
from the saw when cutting metal.
•Remove all traces of wood dust on or around
the saw when cutting metal.
•Remove all metal shavings on or around the
saw before sawing wood again.
Any power saw can throw foreign objects into the
eyes. This can cause permanent eye damage. Wear
safety goggles (not glasses) that comply with ANSI
Z87.1 (shown on package). Everyday eyeglasses
have only impact resistant lenses. They are not safe-
ty glasses. Safety goggles are available at Sears
retail catalog stores. Glasses or goggles not in com-
pliance with ANSI Z87.1 could seriously hurt you
when they break.
•Do not wear loose clothing, gloves, neckties or
jewelry (rings, wrist watches). They can get
caught and draw you into moving parts.
•Wear nonslip footwear.
• Tie back long hair.
• Roll long sleeves above the elbow.
• Noise levels vary widely. To avoid possible hear-
ing damage, wear ear plugs or muffs when using
your saw for hours at a time.
• For dusty operations, wear a dust mask along
with the safety goggles.
Inspect your workpiece.
Make sure there are no nails orforeign objects in the
part of the workpiece to be cut.
Use extra caution with large, very small or awk-
ward workpieces:
•Use extra supports (tables, saw horses, blocks,
etc.) for any workpieces large enough to tip when
not held down to the table top.
•NEVER use another person as a substitute for a
table extension, or as additional support for a
workpiece that is longer or wider then the basic
saw table, or to help feed, support or pull the
workpiece.
•When cutting irregularly shaped workpieces, plan
your work so itwill not pinch the blade. Apiece
of molding, for example, must lay flat or be held
by afixture or jig that will not let it twit, rock or
slipwhile being cut.
•Properly support round material such as dowel
rods, or tubing. They have a tendency to rolldur-
ing a cut, causing the blade to "bite". To avoid
this,always use a "V" block or clamp the work to
the miter gage.
•Cut only one workpiece at a time.
•Clear everything except the workpiece and relat-
ed support devices offthe table before turning
the saw on.