S RVICE AN ADJUST E TS

TO ADJUST CARBURETOR

The carburetor (See Fig. 37) has been pre-set at the factory and readjustment should not be necessary.. However, if the carburetor does need to be adjusted, proceed as follows:

®Close the high speed adjusting screw by hand..

®Do not overtighteno

o Then open it 1-1/4 to 1-1/2 turns°

®Close the id)e adjusting screw by hand, Do not overtighten.

oThen open it 1-1/4 to 1-1/2 turns_

®Start the engine and let it warm up,

oSet the throttle control to FAST. Adjust the high speed adjusting screw in until the engine speed or sound alters° Adjust the screw out until the engine

speed sound alters. Note the difference between the two limits and set the screw in the middle of the

range..

eSet the throttle control to SLOW,. Adjust the idle adjusting screw in until the engine speed drops, then adjust the screw out until the engine speed drops. Note the difference between the two limits and set the screw in the middle of the range..

®If the engine tends to stall under load or not accel- erate from low speed to high speed properly, adjust the high speed screw out in 1/8 turn increments until the problem is resolved°

®Let the engine run undisturbed for 30 seconds between each setting to allow the engine to react to the previous adjustments.

_IDLE

ADJUSTING SCREW

_:j- (Close finger tight only)

(Close finger tight only)

i i Hl=,,Hll ,l= ,

FIG. 37

TO ADJUST:

eClean the spark plug by carefully scraping elec- trodes (do not sand blast or use a wire brush)_

oBe sure the spark plug is clean and free of foreign matedaL Check electrodes gap (See Fig. 38) with a wire feeler gauge and reset the gap to 030 inch if necessary_

.030 GAP

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHlCH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS.

IF YOU THINK THE ENGINE GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOU R NEAREST SEARS SERVICE CENTER, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS,.

TO ADJUST OR REPLACE

THE SPARK PLUG

FIG. 38

TO REPLACE:

eIf you need a new spark plug, use only the proper replacement spark plug.

eSet the gap to _030(See Fig 38).

oBefore installing the spark plug, coat its threads lightly with graphite grease to insure easy removal

•Tighten the plug firmly into the engine,

•Ifa torque wrench is available, to rque the plug to 18 to 23 ft - Ibs

If you have difficulty starting you r snowthrower, you may need to adjust or replace the spark plug. Follow the instructions below.

Replace the spark plug it electrodes are pitted or burned or if the porcelain is cracked

23

Page 22 Page 24
Page 23
Image 23
Sears 536.884811 owner manual To Adjust Carburetor, To Adjust or Replace Spark Plug, To Replace
Page 22 Page 24

536.884811 specifications

The Sears 536.884811 is a well-regarded model of the sewing machine that has gained popularity among hobbyists and professionals alike. Renowned for its robust construction and user-friendly design, this sewing machine encapsulates both functionality and reliability.

One of the standout features of the Sears 536.884811 is its versatility. Equipped with a variety of built-in stitch patterns, it accommodates a wide range of sewing tasks from basic repairs to creative projects. The machine includes essential stitches such as straight, zigzag, and decorative options, making it suitable for different fabrics and styles.

The machine is powered by a reliable motor, ensuring consistent performance even with thicker materials. This is particularly valuable for users who work with a diverse assortment of textiles, from delicate silk to denim. Its adjustable presser foot pressure is a beneficial feature, allowing users to customize the sewing experience to match the fabric being used.

One of the noteworthy technologies integrated into the Sears 536.884811 is the automatic needle threader, which simplifies the threading process and is especially advantageous for those with visual impairments or dexterity issues. This machine also boasts an easy bobbin system, minimizing downtime spent on setup and maximizing productivity.

Ergonomics play a vital role in the design of the Sears 536.884811. Its layout includes a clear and intuitive control interface that enables even novice users to navigate settings easily. Additionally, the work area is well-lit, ensuring optimal visibility while sewing, which is crucial for precision in detailed work.

Storage and portability are other key characteristics that make the Sears 536.884811 a favorite among sewers. The machine often comes with built-in compartments that neatly organize accessories and tools, making it easy to keep everything in order. Moreover, its lightweight design facilitates transport, making it an excellent choice for classes or travel.

In summary, the Sears 536.884811 exemplifies a harmonious blend of classic sewing machine engineering and modern conveniences. With its range of stitch options, ease of use features, and thoughtful design, it serves as an ideal choice for anyone looking to elevate their sewing projects, whether they are beginners or more experienced crafters.
Top Page Image Contents