SECO-LARMELECTROMAGNETIC LOCK

Troubleshooting:

Door does not lock

Check to make sure the wires are securely tightened to the terminal block.

Bond status LED does not Illuminate

Check that the power supply is connected and operating.

 

Use a meter to check the resistance of coils inside the lock. See below.

 

Make sure the rubber washer is installed and free from damage.

 

 

Door locks, but can easily be forced open

Make sure the electromagnet and armature plate are properly aligned.

 

Make sure the contact surfaces of the electromagnet and armature

 

plate are clean and free from rust.

 

Check the power leads with a meter, and make sure 12VDC or 24VDC is

 

present.

 

Use a meter to check the resistance of coils inside the lock. See below.

 

Make sure the rubber washer is installed and free from damage.

 

 

Delay in door releasing

The electromagnet is fitted with a metal oxide varistor to prevent

 

interference, so do not install a second diode.

 

 

No relay output

Check that the power is connected properly and turned on.

 

Make sure the lock is aligned properly.

 

Make sure the NO/NC/COM are wired properly.

If the Electromagnet has low or no holding force, check the resistance of the coils by performing the following steps:

1.Remove the faceplate from the lock.

2.Disconnect the wire harness from the circuit board.

3.Using a meter, measure the resistance across: Red / Green wires, and the Black / White wires.

4.Each coil should test at 48Ω ±10%.

5.If one or both of coils shows an open, short, or incorrect resistance, replace the electromagnet.

Wire Harness:

 

 

48Ω ±10%

White

Black

 

48Ω ±10%

Green

Red

 

LIFETIME LIMITED WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for the lifetime of the product. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. Under no circumstances will SECO- LARM be responsible for any costs or charges for removal, installation, or reinstallation. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO- LARM, and the purchaser’s exclusive remedy, shall be limited to repair or replacement only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else. This lifetime limited warranty is for products sold and installed in the United States and Canada. For all other countries the warranty is 1 (one) year.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

SECO-LARMU.S.A., Inc.

 

16842 Millikan Avenue, Irvine, CA 92606

Website: www.seco-larm.com

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326

E-mail: sales@seco-larm.com

PITGW1 MiE941SA_1009.docx

8

SECO-LARM U.S.A., Inc.

Page 7
Page 8
Image 8
SECO-LARM USA E-941SA-600PQ, E-941SA-1K2PQ manual Troubleshooting, Wire Harness, SECO-LARMU.S.A., Inc
Page 7

E-941SA-1K2PQ, E-941SA-600PQ specifications

SECO-LARM USA has established itself as a reputable provider of security solutions, and its E-941SA series is a testament to this commitment. Among the notable products in this series are the E-941SA-1K2PQ and the E-941SA-600PQ, both of which offer advanced features indispensable for modern security applications.

The E-941SA-1K2PQ is a high-performance exit button that provides both reliability and versatility. One of its main features is the self-resetting function. This allows the button to reset automatically after being pressed, making it efficient for high-traffic areas where multiple users need to exit quickly. With its rust-resistant stainless-steel construction, the E-941SA-1K2PQ is designed for durability, even in challenging environments. The button is equipped with an LED indicator light that provides visual feedback, confirming that the system is armed and operational. This feature is particularly beneficial for visually impaired individuals or in low-light situations.

On the other hand, the E-941SA-600PQ is a panic exit switch that emphasizes safety and ease of use. This model features a large, easy-to-press button, making it accessible for users of all ages and abilities. The device is designed to be mounted on walls, and its sleek profile allows it to blend seamlessly into various environments. With a durable weather-resistant casing, the E-941SA-600PQ is suitable for both indoor and outdoor applications.

Both models utilize advanced technology, including a 1A relay output, allowing them to interface with a variety of security systems, such as access control panels and alarm systems. Integration is further simplified with a voltage range of 12 to 24VDC, accommodating multiple setup preferences. Importantly, the E-941SA series is also designed to conform to relevant safety standards, ensuring that they meet industry regulations.

In conclusion, the SECO-LARM USA E-941SA-1K2PQ and E-941SA-600PQ represent innovative solutions in security and access control. With self-resetting capabilities, durable construction, and user-friendly designs, these exit buttons exemplify the blend of safety, reliability, and technological sophistication. As the demand for effective security solutions continues to grow, the E-941SA series stands out as a trusted choice for both residential and commercial applications.
Top Page Image Contents