Introduction
Overview
The KE-265 is an easy to program, easy to use, stand-alone Keyless Entry® system with features suitable for basic access control requirements. Providing either a voltage output or dry contact closure, the KE-265 is designed to control any fail-safe or fail-secure electric locking device.
The KE-265 features one master code and five user codes. Two relay outputs are available to provide a variety of access control configurations including single door operation with an auxiliary output for a CCTV/Light Controller, a Gate/Garage Door controller or Doorbell activation or the KE-265 can be configured for two door operation.
System Specifications
Input Requirements: | 12 to 24V AC/DC |
Standby Current Draw: | 12V Î 10 mA |
| 24V Î 25 mA |
Outputs: | 2 SPDT Relay contacts at 6 amps (120VAC) |
| Voltage or Dry Contact |
| Fail Safe or Fail Secure Relay Configuration |
Programmable Output: | 1 to 120 seconds |
(Door Open Time) | Default Î 5 seconds |
Latching: | Manual (Toggle On/Off) |
# of User Codes: | 6 Codes (1 Master, 5 User) |
Code Length: | 3 to 8 Digits |
Default Master Code: | 1-3-5-7-9 |
Tamper Alarm: | 25 Incorrect Key Presses |
Access Code Protection: | Non-Volatile Memory |
Keypad Operating | - 40° C to + 70° C (- 40° F to + 160° F) |
Environment: | 100 % Relative Humidity |
Keypad Dimensions: | KP-5S, KP-5SL Î 6 ⅝” x 2 ¼” x ½” |
5 Pad Non Illuminated |
5 Pad Illuminated | KP-5DI, KP-5SI Î 6 ½” x 1½” x ⅞” |
12-Pad 3x4 | KP-34S, KP-34K, KP-34B Î 5 ⅛” x 3 ⅜” x 7/16” |
Thinline 2x6 | KP-26TS, KP-26TB, KP-26TI, KP-26TR Î 7 ⅛” |
| x 1 ¾” x ¾” |
Control Module Operating | - 40° C to + 49° C (- 40° C to + 120 ° F) |
Environment: | |
Control Module Dimensions: | 7½“ x 5½“ x 2½“ |
Input Requirements
The KE-265 accepts 12 to 24 volts AC/DC. An optional battery charging module and rechargeable Gel Cells are available to keep the system operational for up to 24 hours during a power interruption. System current draw (maximum):
Standby: 10mA at 12 volts, 25mA at 24 volts
During Operation: .25 amps max (with illuminated Keypad)
⊗IMPORTANT: The maximum current draw allowed is 1 amp. (3 amps with battery back-up for fail-secure applications only.) Check the specifications of your locking device. Make sure that the locking device and the KE-265 (.25 amps) combined draw less than 1 amp. For locking devices that draw more current, a separate power supply is required. (See Appendix B
– Page 24)
Note: If connecting DC, make the connections to “DC IN/OUT” instead of “12-24V AC/DC IN” (see Circuit Board Layout – Page 23). Make sure the polarity is correct.
Output Capabilities
The KE-265 provides two SPDT dry contact relays (rated at 6 amps at 120 VAC). Each relay can be configured to perform one of many different functions depending on the specific access control requirement. User Authorization to control each relay is determined by Setting Relay Options (see System Hardware Setup Î page 10). Each relay can be configured for one of the following options:
1.Voltage Output – For any Fail Safe or Fail Secure Locking Device
2.Dry Contact Output – For control of Gate Operator or Garage Door
3.CCTV or Light Controller – First key press triggers a 10 second output
4.Doorbell – Press ∗ at the Keypad to trigger a 1 second output for a doorbell (not included). This function is only available with a 12 Pad 3x4 or Thinline 2x6.
5.Auxiliary Output – Momentary or Manual Control of an electronic device.
