Security 100 KE-265 manual Programming User Codes, Programming Door Open Time, Default Î 5 seconds

Programming User Codes

To Program a New User Code or Change an Existing User Code:

1.Choose a new 3 to 8 digit code that will be used for this User Code. ___ ___ ___ ___ ___ ___ ___ ___

2.Decide which User Location to place this User Code (see Overview of User Codes)

3.Enter the Master Code, followed by the User Location (you will hear three rapid beeps) and immediately enter the new User Code. (Do not let more than five seconds elapse between entries or the system will reset!!!)

Example: 1-3-5-7-9 1-1-1 1-2-3-4

4.After entering your new code, wait five seconds for the 3 reset beeps.

To Delete a User Code

1.Enter the Master Code, followed by the User Location of the User Code you want to delete (you will hear

three rapid beeps). Example: 1-3-5-7-9 1-1-1

2.Wait five seconds for the 3 reset beeps (Do not enter any digits until you hear 3 reset beeps)

Programming Door Open Time Default Î 5 seconds

To Program/Change the Door Open Time for the Master Code and User Code 1 and 2:

1.First determine the length of time you wish to program as the Door Open Time for these users. This is the length of time the door will remain open after a valid Master Code, User Code 1 or User Code 2 has been entered into the system.

 Note: For controlling a garage door or electric gate, you will need to set the door open time to 1 second

2.Locate the Control Module, remove the cover and locate the “PROGRAM” switch on the circuit board.

3.Press the PROGRAM switch once *. (The Keypad will beep rapidly 4 times)

4.At the Keypad, enter 1-1-1-7 to open the memory (you will hear three rapid beeps) and enter a combination of “1’s” (for every one second increment) and

16

“5’s” (for every five second increment) that equal your desired Door Open Time. Each valid key press (a “1” or a “5”) will generate a double beep. (Do not let more than five seconds elapse between entries or the system will reset!!!)

Example: “1-1-1-7 5-5-5-1-1” Î 17 seconds

5.After entering your Door Open Time, wait five seconds for the 3 reset beeps.

To Program/Change the Door Open Time for User Code 3,4 and 5: (Rev B and later)

1.First determine the length of time you wish to program as the Door Open Time for these users. This is the length of time the door will remain open after a valid User Code 3, User Code 4 or User Code 5 has been entered into the system.

 Note: For controlling a garage door or electric gate, you will need to set the door open time to 1 second.

2.Locate the Control Module, remove the cover and locate the “PROGRAM” switch on the circuit board.

3.Press the PROGRAM switch once *. (The Keypad will beep rapidly 4 times)

4.At the Keypad, enter 1-1-1-5 to open the memory (you will hear three rapid beeps) and enter a combination of “1’s” (for every one second increment) and “5’s” (for every five second increment) that equal your desired Door Open Time. Each valid key press (a “1” or a “5”) will generate a double beep. (Do not let more than five seconds elapse between entries or the system will

reset!!!)

Example: “1-1-1-5 1-1-5” Î 7 seconds

5.After entering your Door Open Time, wait five seconds for the 3 reset beeps.

Notes: * Once the PROGRAM switch has been pressed, you have 2 minutes to begin programming. You will hear a double beep with each valid key press. Once you begin entering the combination of 1’s and 5’s do not let more than five seconds elapse between entries or the system will reset!!! Maximum Door Open Time is 120 seconds.

17