Security 100 KE-265 manual The Installation Procedure, Required Tools

The Installation Procedure

Required Tools

You will need the following tools:

• Medium sized, Phillips head	•	7/8” or 1” (25mm) drill bit
screwdriver	•	1/2” (16mm) drill bit

•1/8” standard screwdriver • 5/32” (4mm) drill bit (For 12-Pad 3x4)

• Drill • 3/16” (6mm) drill bit (For 5-Pads & Thinline 2x6)

Prepare the Keypad for Installation

There are different procedures for mounting each Keypad. Locate the Keypad part number on the back of the Keypad and follow appropriate mounting instructions below. Keypad templates are included with each Keypad (except KP-34’s) to assist with the installation.

Mounting Instructions 5 Pad Non Illuminated: KP-5S and KP-5SL

1.Select flat mounting surface 3" X 7".

2.Use “Template A” (included with the Keypad) to mark locations of holes A, B, and C.

3.Locate and drill the large hole marked “A”. Hole must be at least 7/8" (22mm) diameter.

4.Hold the Keypad against the wall with the connector through hole “A”. Check markings for hole “B”. Re-mark if required. If using plastic anchors, drill hole “B” using 3/16" (6mm) bit. NOTE: Plastic anchors are provided for some mounting applications. If anchors are not used, holes “B” and “C” must be smaller than 3/16".

5.Using the template, verify the hole marked “C” is aligned and then drill hole “C”.

6.Install the metal mounting bracket into hole “C” with the screw provided.

7.Do NOT mount Keypad at this time.

8.Proceed to Install the Wiring Cable.

Mounting Instructions 5 Pad Illuminated: KP-5DI and KP-5SI

1.Select a flat surface 1 ¾" X 7".

2.Use “Template B” (included with the Keypad) to mark holes A, B and C.

3.Locate and drill the large hole marked “A”. Hole must be at least 7/8" (22mm) diameter.

4.Check markings for holes “B” and “C”. Re-mark if required. Drill holes ”B” and “C” using 3/16" (6mm) bit.

5.Install the metal mounting bracket with the screws provided.

6.Do NOT mount Keypad at this time.

7.Proceed to Install the Wiring Cable.

Mounting Instructions 12 Pad 3x4: KP-34S,KP-34B or KP-34K The 3x4 keypad is designed to mount to a single gang switchbox or on a wall, pedestal or any flat surface of at least 3

½by 5 ¼”. The composition of the mounting surface will determine the fastening method required. If mounting to a surface other than a switchbox:

1. Select a flat surface (3 ½” by 5 ¼”) near the door where you wish to install the keypad.

2. Drill the large hole for the Keypad connector using a 7/8” (25mm) drill bit.

3. Place the connector on the back of the keypad in the large hole. Mark the keypad mounting holes.

4. Drill clearance holes in accordance with fastening method used. (If mounting to wood, drill small pilot holes and use #6 flat head wood screws provided. If mounting to metal, drill two 5/32" clearance holes for #6 flat head machine screws provided.)

5. Do NOT mount the keypad at this time.

6. Proceed to Install the Wiring Cable.

Mounting Instructions Thinline 2x6: KP-26TS, KP-26TI, KP-26TB or KP-26TR

The Thinline 2x6 is designed for mullion mount applications. It can also be mounted on a wall, pedestal or any flat surface of at least 1 ¾” by 7”. The composition of the mounting surface will determine the fastening method required:

1.Select a flat surface (1 ¾ ” by 7”) near the door where you wish to install the keypad.

2.Using the Thinline template, mark location of holes.

3.Drill the large hole using a 1” (25mm) drill bit.

4.Place the connector on the back of the keypad in the large hole to verify that the mounting holes are aligned. Make adjustments if necessary.

5.Drill mounting holes in accordance with fastening method used. If mounting to wood, drill small pilot holes and use #6 flat head wood screws provided. If mounting to metal, drill two 5/32" clearance holes for #6 flat head machine screws provided.

6.Do NOT mount the keypad at this time.

7.Proceed to Install the Wiring Cable.

6 7