STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page.
Be sure to use only genuine SHARP parts and supplies.
| Indication |
| Cause and remedy | Page |
| Developer | Steadily | Developer is required. contact your authorised | 35 |
| replacement | |||
| lit | service representative. | ||
| required indicator |
| ||
|
|
|
| |
|
|
|
|
|
| Toner cartridge | Steadily | Replacement of Toner cartridge will be needed | 24 |
| lit | soon. Prepare a new cartridge. | ||
| replacement |
| ||
|
| Toner cartridge must be replaced. Replace it |
| |
| required indicator | Blinking | 24 | |
| with a new one. | |||
|
| |||
|
|
| A misfeed has occurred. Remove the misfed |
|
| Misfeed indicator | Blinking | paper referring to the description of "MISFEED | 31 |
| REMOVAL". |
| ||
|
|
| The lower side cover may be open. If so, close it. | 34 |
| Maintenance | Steadily | Service by an authorised SHARP service | 35 |
| indicator | lit | technician is required. | |
|
| |||
|
|
|
|
|
| SPF misfeed | Blinking | An original misfeed has occurred in the SPF. |
|
| Remove the misfed originals referring to the | 34 | ||
| indicator | |||
|
| description of "E: Misfeed in the SPF |
| |
|
|
|
| |
|
|
|
|
|
|
|
| The unit is in the preheat mode. Press any key to | 21 |
| Power save indicator is | cancel the preheat mode. | ||
|
| |||
| The unit is in the auto power |
| ||
| steadily lit. |
|
| |
|
| Press the start ( ) key to cancel the auto power | 21 | |
|
|
| ||
|
|
|
| |
|
|
|
| |
| The paper tray indicator is | The paper tray is not installed properly. Push the | – | |
| blinking. |
| tray into the unit securely. | |
|
|
| ||
|
|
|
|
|
|
|
| The toner cartridge is not installed. Check if the |
|
| "CH" is blinking in the | cartridge is installed. If "CH" is blinking even if a | – | |
| display. |
| cartridge is installed properly, contact your | |
|
|
| ||
|
|
| SHARP service centre immediately. |
|
| "CH" is steadily lit in the | Side cover is open. Close the side cover |
| |
| securely by pressing the round projections near | – | ||
| display. |
| ||
|
| the side cover open button. |
| |
|
|
|
| |
|
|
| The paper tray or | 8 |
|
|
| Load paper. | |
|
|
|
| |
|
|
| A misfeed has occurred in the paper tray, single |
|
| "P" is blinking in the display. | bypass or | 31 | |
|
|
| paper. |
|
|
|
| Paper tray is not securely installed. Push the tray | – |
|
|
| in securely. | |
|
|
|
| |
| A letter and a number appear | The scan head locking switch is locked. Unlock |
| |
| the scan head locking switch and turn the power | 36 | ||
| alternately. |
| switch off/on. |
|
|
|
|
| |
|
|
|
|
|
|
|
| The unit will not function. Turn the power switch |
|
| A letter and a number appear | off and then switch it on, and if there is again an | – | |
| alternately. |
| error, remove the power cord from the outlet, | |
|
| and contact your authorized service |
| |
|
|
|
| |
|
|
| representative. |
|
30