Sharp LC-26SV490U PC control of the TV, Communication conditions, Communication procedure

Appendix

RS232 Port Specifications

PC control of the TV

•Attach an RS-232C cable cross-type (commercially available) to the supplied Din/D-Sub RS-232C for the connections.

•This operation system should be used by a person who is accustomed to using computers.

Communication conditions

Set the RS-232C communication settings on the PC to match the TV's communication conditions.

The TV's communication settings are as follows:

Baud rate:	9,600 bps
Data length:	8 bits
Parity bit:	None
Stop bit:	1 bit
Flow control:	None

Communication procedure

Send the control commands from the PC via the RS- 232C connector.

The TV operates according to the received command and sends a response message to the PC.

Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command.

Command format

Eight ASCII codes +				CR
	C1	C2	C3		C4	P1	P2	P3	P4
Command 4-digits
								digits Return code
					Parameter 4-

Command 4-digits: Command. The text of four characters.

Parameter 4-digits: Parameter 0–9, x, blank, ?

Parameter

Input the parameter values, aligning left, and fi ll with blank(s) for the remainder. (Be sure that 4 values are input for the parameter.)

When the input parameter is not within an adjustable range, “ERR” returns. (Refer to “Response code format”.) Any numerical value can replace the “x” on the table.

0				When “?” is input for some
				commands, the
0	0	0	9	present setting	?
				value responds.
	3	0			?	?	?	?

Response code format

Normal response		Problem response (communication
		error or incorrect command)
O	K
		E	R	R
Return code (0DH)					Return code (0DH)

Command table

Commands not indicated here are not guaranteed to operate.

CONTROL ITEM		COMMAND				PARAMETER					CONTROL CONTENTS
POWER ON COMMAND SETTING		R	S	P	W	0			_	Off	The Power On command rejected.
						1	_	_	_	On	The Power On command accepted.
POWER SETTING		P	O	W	R	0	_	_	_	Power Off	It shifts to standby.
						1	_	_	_	Power On	The Power On Command must be waited until system is completely Power Off (LED power
											indicator turns to be Red)
	TOGGLE	I	T	G	D	x				(Toggle)	It input-switches by the toggle. (It is the same as an input change key)
INPUT SELECTION A	TV	I	T	V	D	0					It input-switches to TV. (A channel remains as it is. (Last memory))
	INPUT1-8	I	A	V	D	*				Input terminal number (1–8)	It input-switches to INPUT1~INPUT8.
AV MODE SELECTION		A	V	M	D	*				0:(Toggle) ,1:STANDARD,2:DYNAMIC,3:MOVIE,	Although it can choose now, it is toggle operation in inside.
										4:POWER SAVER,5:USER
VOLUME		V	O	L	M	*	*			Volume (0–100)
	H-POSITION	H	P	O	S	*	*	*		Only PC mode. (0–100,menu disolay range+/-50)	The screen position variable ranges depend on the View Mode or the
	V-POSITION	V	P	O	S	*	*	*		Only PC mode. (0–40,menu display range+/20)	signal type. The ranges can be seen on the position-setting screen.
POSITION	CLOCK	C	L	C	K	*	*	*		Only PC mode. (0–180,menu display range+/-90)
	PHASE	P	H	S	E	*	*	*		Only PC mode. (0–40,menu display range+/-20)
											0: Although it can choose now, it is toggle operation in inside.
											1: [AV] Only available when SD content is being input.
											[PC-32’’] Only available when 720X480 and 1280x720 are being input.
		W	I	D	E	*					[PC-46’’&PC-26’’] Available except when 1920X1080 is being input.
										0:(Toggle) 1:Normal 2:S.Stretch 3:Stretch 4:Zoom	2,3,4: [AV] Only available when AV signal is being input.
VIEW MODE										5:Full Screen 6:Dot by Dot 7:Cinema)	5: [AV] Only available when 720P is being input.
											[PC] Available except when 1280x720 and 1920x1080(46’’&26’’)are being input.
											6: [PC] Available except when 1600x1200 and 1280x1024 (32’’only) and 1400x1050
											(32’’only) are being input.
											7: [PC] Available except when 1360x768 and 1280x720 and 1920x1080 (46’’&26’’) are
											being input.
MUTE		M	U	T	E	*	_	_		0: (Toggle), 1: On, 2: Off
SURROUND		A	C	S	U	*				0: (Toggle), 1: On, 2: Off
AUDIO SELECTION		A	C	H	A	x	_	_	_	(Toggle)
SLEEP TIMER		O	F	T	M	*				0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN.,
										3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.
	DIRECT	D	C	C	H	*	*	*		The channel number of TV	An input change is included if it is not TV display.
	CHANNEL									(1–135)	In Air, 2–69ch is effective.
	(ANALOG)										In Cable, 1–135ch is effective.
	DIRECT	D	A	2	P	*	*	*	*	(0100-9999)	DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
	CHANNEL	D	C	2	U	*	*	*	_	(1-999)	DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
	(DIGITAL)										Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
CHANNEL
		D	C	2	L	*	*	*	_	(0-999)	DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
											Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
		D	C	1	0	*	*	*	*	(0-9999)	DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
		D	C	1	1	*	*	*	*	(0-6383)	DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
	CH UP	C	H	U	P	x				The channel number of TV +1
	CH DOWN	C	H	D	W	x				The channel number of TV –1	If it is not TV display, it will input-switch to TV. (same function as CH<)
CC		C	L	C	P	x				(Toggle)	Toggle operation of a closed caption.

•If an underbar (_) appears in the parameter column, enter a space.

•If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.

•Any numerical value can replace the “x” on the table.

48