Sharp LC-37GA8E, LC-37BV8E, LC-32GA8E, LC-32BV8E operation manual Hdmi Setup, Colour System, Demo

Menu operations

DNR (Digital Noise Reduction) TV/AV only

Menu Operation: A (page 11)

Produce a clearer image. (Off, High, Low)

HDMI Setup AV only

HDMI (High-Definition Multimedia Interface) terminal selection.

1 To watch an HDMI equipment image, select “EXT5” from “INPUT SOURCE” menu using b on the remote control unit or TV.

2 Press MENU and the MENU screen displays.

3 Press c/dto select “Option”.

4 Press a/b to select “HDMI Setup”, and then press OK.

•“HDMI Setup” is displayed only when “EXT5” is selected from the INPUT SOURCE menu.

MENU [Option ... HDMI Setup]

Option

Audio Only

DNR[Off]

HDMI Setup

Quick Shoot	[On]
Demo

5	Press a/bto select the desired item, and then
	press OK.
6	Press a/b/c/dto select the desired setting, and
	then press OK.
HDMI Setup		Selectable items	Description
items
Signal		RGB/YCbCr 4:4:4/	Select the video signal
Type*		YCbCr 4:2:2	type from the HDMI
			terminal.
Colour		ITU601/ITU709	Select the internal colour
Matrix*			space conversion method
			when an RGB signal is
			input.
Dynamic		Normal/	Select the signal amplitude
Range*		Enhanced	range. Usually, select
			“Normal”.
Auto View		Disable/Enable	Set whether or not to use
			WIDE MODE based on
			signal recognition,
			including an HDMI signal.
Audio		Digital/Analogue	Select “Digital” for audio
Select			signal via the HDMI
			terminal. Select “Analogue”
			for audio signal via the
			AUDIO jack.

NOTE

•Refer to your external equipment operation manual for the signal type.

•Items with * may be greyed out (with 4) depending on the type of signal input from the external equipment.

Input Select

Menu Operation: A (page 11)

For setting the signal type of external equipment.

Input source	Signal type
EXT 1	Y/C, CVBS, RGB
EXT 2	Y/C, CVBS, RGB
EXT 3	AUTO
EXT 4	PC (RGB), COMPONENT (Y, PB, PR)

NOTE

•If no (colour) image displays, try to change the other signal type.

•Check the operation manual of the external equipment for the signal type.

•TV, EXT3 and EXT5 are not displayed in Input Select.

•If both CVBS and RGB signals are input to EXT 1 or EXT 2 using a SCART cable, the TV may output an RGB signal even though you have designated CVBS for the respective terminal. This happens due to the setting of your external equipment.

Quick Shoot

Menu Operation: A (page 11)

Improve LCD response when viewing fast-moving images. The effect is greater at low room temperatures (at or below 15˚C).

NOTE

•Quick Shoot may cause image noise. If this occurs, set the function to “Off”.

Colour System TV/AV only

Menu Operation: A (page 11)

You can change the colour system to one that is compatible with the image on the screen. (AUTO, PAL, SECAM, NTSC3.58, NTSC4.43, PAL-60)

NOTE

•Factory preset value is “AUTO”.

•If “AUTO” is selected, colour system for each channel is automatically set. If an image does not display clearly, select another colour system (e.g. PAL, SECAM).

•“NTSC3.58”, “NTSC4.43” and “PAL-60” cannot be selected in TV tuner mode.

Demo TV/AV only

Menu Operation: C (page 11)

When activated, this function demonstrates some of the functions of the TV on the screen.

Item

Demo: Sets whether to activate the function.

Input Source: Selects whether to demonstrate all functions of connected terminals or skip some.

Teletext: Sets whether to demonstrate Teletext.

Freeze: Sets whether to demonstrate Freeze.

Menu: Sets whether to demonstrate Menu.

Interval: Sets the interval between the presentations.

NOTE

•Some demonstrations may not be presented depending on the settings made above.

•After switching on this demo function, it takes 70 seconds approximately, before the TV-set starts the demo show. The selected functions are shown in a self-repeating sequence. Return to normal television-mode is possible only by deactivating the demo-function.

18