Sharp PN-R603 Menu Items nSCHEDULE, Press or to select the SCHEDULE number, and press, Power

Menu Items

nSCHEDULE

You can set the time to switch the monitor on and off.

Set this function with SCHEDULE in the SETUP menu. (See page 24.)

SCHEDULE										D-SUB[RGB]
		(2)	– –/– –/– – – –			– – –			– –:– –:– –	(5)	(6)
No. (1)				(3)			(4)
		POWER	DAY OF THE WEEK				TIME			INPUT	BRIGHT
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	–	– –	–	– –	-	– –	– –	:	– –	– –	– –
	1 9 2 0 x 1 0 8 0					OK···[ENTER] CANCEL···[RETURN]
					V: 60 Hz		H: 67.5 kHz

1.Press or to select the SCHEDULE number, and press .

2.Set the SCHEDULE. (See the description below.)

Press or to select items, and press or to change the setting.

3.Press ENTER.

SCHEDULE becomes effective.

(1)

●: SCHEDULE effective

-: SCHEDULE not effective

(2) POWER

ON : Switches the monitor on at the specified time.

OFF : Switches the monitor off at the specified time and puts the monitor in standby mode.

(3) DAY OF THE WEEK

Specifies the day of the week to execute the SCHEDULE. 0:ONLY ONCE

Executes the SCHEDULE once on the specified day. Specify the day of the week to execute the SCHEDULE.

1:EVERY WEEK

Executes the SCHEDULE on the specified day of the week every week. Specify the day of the week to execute the

SCHEDULE.

Periodic setting such as “Monday through Friday” is also possible.

2:EVERY DAY

Executes the SCHEDULE every day regardless of the day of the week.

(4) TIME

Specifies the time to execute the SCHEDULE. Set the time on a 24-hour basis. (Factory default)

Can be entered as 12-hour time using the TIME setting in

DATE/TIME FORMAT.

(5) INPUT

Specifies the input mode at power-on. If you don’t specify this the input active at the last power-off will appear. Input modes displayed on HDMI1, HDMI2 and D-SUB will depend upon the INPUT SELECT settings.

(6) BRIGHT

Sets the brightness when changing the screen brightness at a specified time.

Caution

•Do not switch off the main power after setting the

SCHEDULE.

•Specify the correct date and time. (See page 24.)

SCHEDULE does not function unless the date and time are specified.

•Check regularly that the set date and time are correct.

•When STANDBY MODE is LOW POWER, SCHEDULE cannot be set.

•When a temperature abnormality occurs and the backlight brightness is reduced, the brightness is not changed even if a schedule set to BRIGHT is executed.

TIPS

•Up to 8 SCHEDULE items can be registered.

•Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode.

•A SCHEDULE that has a large number has precedence over that of a small number when schedules overlap.

E30