Assembly

Prior to assembly

 

 

Using Figure above as a guide, familiar-

Powerhead Assembly

ize yourself with the Shindaiwa P231

Lower Tube Assembly

pole pruner and its various components.

Upper Tube/Saw Assembly, Chain and

Understanding your unit helps ensure

top performance, longer service life, and

Guide Bar

Chain CoverTool Kit Containing:

safer operation.

 

Spark Plug Wrench

Before assembling, make sure you have

4mm Hex Wrench

all the components required for a com-

8 x 10mm Spanner

plete unit:

Carefully inspect all components for damage.

 

IMPORTANT!

The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation.

WARNING!

Do not make unauthorized modifications or alterations to your pruner or its components.

Powerhead Installation

1.Place the powerhead on a clean, flat surface, spark plug facing up.

2.Use the 4mm hex wrench to loosen the tube clamp screw. Verify that the D-shaped shim washer is positioned as shown below.

Tube Clamp

Hex

Wrench

3.Add some moly-type EP grease to splines at the end of the main shaft.

CAUTION!

Do not force the shaft tube into the powerhead! Excessive force can damage the shaft tube and mainshaft.

4.Slide the outer tube into the tube clamp until the tube bottoms. If installation is difficult, rotate the outer tube or main shaft slightly until you feel the mainshaft splines engage with the powerhead. Outer tube needs to be inserted so that the end of the grip hits joint cap.

5.Position the outer tube so that the igni- tion switch is facing up and the throttle lever is facing down.

Bar and Chain Options

8 inch Bar — 90SG-33E Chain

10 inch Bar — 90SG-39E Chain

12 inch Bar — 90SG-44E Chain

6.Slide the outer tube into the powerhead until the throttle grip just contacts the tube clamp.

7.Tighten the clamp screw firmly.

 

 

Main

Tube

 

 

Clamp

 

Outer

Shaft

 

 

Tube

 

 

Ignition

Grip

 

 

Switch

 

 

 

 

 

 

Clamp Screw

 

Throttle Lever

Connecting the Throttle Cable

Remove The Cylinder Cover

1.Remove the spark plug boot.

2.Remove the two lower cylinder cover screws.

3.Loosen the top cylinder cover screw until the cover is free of the engine. (The top cylinder cover screw is captive). Lift the cylinder cover off of the engine.

Top Cylinder

Cover Screw

Hex Wrench

Spark Plug

Boot

Lower Cylinder

Cover Screws

Page 7
Image 7
Shindaiwa P231 Assembly, Prior to assembly, Powerhead Installation, Bar and Chain Options, Connecting the Throttle Cable

P231, 62888-94013 specifications

Shindaiwa has long been recognized for its commitment to quality in outdoor power equipment, and the model 62888-94013, specifically the P231, is no exception. This efficient and robust handheld blower is designed for both professionals and homeowners who demand reliable performance for leaf and debris management.

One of the standout features of the Shindaiwa P231 is its impressive air velocity. With a maximum air speed of 175 mph, this blower can tackle even the most stubborn leaves and debris with ease. This powerful airflow is complemented by a lightweight design, making it easy to maneuver even during extended use. Weighing just around 9.8 lbs, the P231 minimizes operator fatigue, allowing for longer periods of operation without discomfort.

Powering the P231 is a reliable 23.9 cc two-stroke engine, engineered for efficient fuel consumption and reduced emissions. This engine technology not only adheres to environmental standards but also provides a perfect balance of power and efficiency. The use of Shindaiwa’s proprietary engine design ensures that the blower can perform consistently regardless of the conditions, whether it’s wet leaves in the fall or light debris in the spring.

Another noteworthy feature of the P231 is its durable construction. Built with high-quality materials, the blower is designed to withstand the rigors of frequent use. The ergonomic handle is designed for comfort, ensuring a secure grip that reduces vibration and enhances control during operation. Furthermore, the blower includes a user-friendly start system that makes kick-starting the engine a hassle-free experience.

Shindaiwa also prioritizes ease of maintenance in the P231 model. It is equipped with a simple air filter access and a fuel tank designed for easy refueling. This attention to user-friendliness ensures that you can keep your equipment in top condition with minimal effort.

In summary, the Shindaiwa 62888-94013 P231 is a dynamic handheld blower that combines power, efficiency, and durability. Ideal for both professional landscapers and homeowners, its features like high air velocity, quality engine technology, lightweight design, and ease of maintenance make it an excellent choice for effective outdoor cleanup. Whether it’s for a large property or routine yard work, the P231 delivers reliability and outstanding performance every time.