Manuals / Powerware / Computer Equipment / Power Supply

Powerware 208/120V, 400/230V, 380/220V Configure the following settings for the selected breaker

Models: 415/240V 380/220V 208/120V 400/230V

1 72

Download 72 pages 60.53 Kb

Page 39

INSTALLATION

9.The selected breaker is highlighted in bold in the schedule. The breaker’s configuration details display in the right half of the page.

Click the breaker to configure. The breaker number highlights and its details display at right.

10.Configure the following settings for the selected breaker:

Breaker Setting	Description

Num Phases	Specify the number of phases (1–3).

Breaker Rating	Specify the branch breaker rating (in amps).

Warning Level	Specify the warning threshold level (in percent load).

Alarm Level	Specify the alarm threshold level (in percent load).

CT Ratio	Specify the current transformer ratio (75A).
	NOTE The selected ratio converts to the value 71.9.

NOTE To revert any changes made on the current page back to default settings before saving, click Reload Breaker Config.

11.Repeat Steps 9 and 10 to configure the remaining breakers in the panel.

12.Click Save Breaker Config to save the settings to the EMS−UGK.

13.Repeat Steps 8 through 12 to configure the breakers in the remaining panels.

14.Click Disconnect to disconnect from the EMS−UGK. Verify that Connected" displays at the bottom of the page.

15.Close the software configuration tool and remove the configuration cable.

16.Activate the reset switch on the bottom of the electronics module: hold the switch for 10 seconds or until the display (if installed) turns off, then release the switch.

17.Continue to

EATON Powerware® Energy Management System (EMS) Upgrade Kit User’s Guide S 164201724 Rev 1 www.powerware.com

33

Image 39

Powerware 208/120V, 400/230V, 380/220V, 415/240V manual Configure the following settings for the selected breaker

Contents

Upgrade Kit 208/120V, 380/220V, 400/230V, 415/240V User’s Guide Powerware Energy Management System EMSRequesting a Declaration of Conformity Three−phase alternating current PROTECTIVE CONDUCTOR TERMINAL Special SymbolsPage Setup Options Table of ContentsInstallation Initial System ConfigurationTroubleshooting Serial Port ServiceMaintenance SpecificationsIntroduction ChapterThe following options for the EMS−UGK are available C A U T I O N IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSSafety Warnings D A N G E RD A N G E R CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONSConsignes de sécurité A T T E N T I O NA C H T U N G WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWARENSicherheitswarnungen W A R N U N GP R E C A U C I Ó N INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONESAdvertencias de Seguridad P E L I G R OChapter InstallationInspecting the Equipment Unpacking the CabinetVerify that the following items are included with the EMS−UGK Checking the Parts ListS Phillips #2 screwdriver Tools RequiredS Pliers or other appropriate tool for installing wire taps To assemble the components, the following tools may be neededInstalling the Hardware Verify that at least two wall anchors attach to studs within the wall Figure 4 shows the location of the two serial ports C A U T I O N Electrical ConnectionsW A R N I N G C A U T I O NS If installing conduit not supplied, plan for adequate conduit Panel Connections and Figure 5. Wiring Overview Example InstallationTable 4. Harness Sizing A, B, CFigure 6. Harness Connections at the Electronics Module Table 5. EMS−UGK Harness ConnectionsMain Input Harness CTM Figure 7. Panel Detail EMS−UGK−LV Model with Dual Panel Option Shown INSTALLATIONIf installing dual panels, repeat Step 5 for the second panel Coil and secure any excess cable away from other conductors Install each CT around the appropriate subfeed breaker wire 12. Choose an option for connecting the phases for voltage sensing C A U T I O NC A U T I O N Proceed to Step 15 on page Verify the wire taps are completely closed around the wires 24. Continue to the following section Installing the Software Configuration Tool Initial ConfigurationInitial System Configuration Window Figure 15. System Status Page Connected7. Configure the following required settings voltage. For example, for two 225A panels and a 120V nominalCalc to have the software automatically calculate the VA rating 9. Click Save Sys Config to save the settings to the EMS−UGK. Depending on communication speed, updates take effect within 15-20 seconds 12. Configure the following Miscellaneous Features 13. Configure the following Building Alarm Settingssounds for each new alarm and can be turned off by Configuration Using the Software Configuration Tool 4. Configure the following settings for the selected panel 6. Repeat Steps 3 through 5 to configure the remaining panelsmain panel breaker alarms and zeroes the panel percent 10. Configure the following settings for the selected breaker Initial Panel and Breaker Configuration Using the Display INSTALLATION 12. Continue to the following section, InstallationAdvanced Metering Installation Chapter Reset FunctionOperation Breaker NumberingThe following table shows the indicator status and description Control Panel FunctionsPROFILE SETUP SET UP 000.0 000.0 000.0Display Functions EATON EMS−UGKThe following tables show the basic menu structure Menu MapTable 8. Breaker Meters Table 7. Panel MetersUse the arrow keys to enter the new password A-Z Setup OptionsUse the arrow keys to enter the password for the level you want to access, then select DONE to display the options forControl Panel Configuration Accessing ConfigurationConfiguring Panels Containing Branch Circuit Breakers Panel breaker rating in amps Configuring Panels Containing Subfeed BreakersSubfeed breaker rating in amps NOTE Configure a breaker only if its CT is installed Configuring Branch Circuit Breakers7. When all branch circuit configuration is complete, select the Viewing Breaker Meters Viewing Panel MetersChapter 4 Communication Installing Communication Features Serial Port ServiceCommunication Options X−Slot Card Control Terminals Relay Output Contacts Alarm Relay Programmable Signal Inputs Building AlarmsW A R N I N G COMMUNICATION Updating the Firmware MaintenanceReplacing the Power Xpert Gateway Series 1000 Card Recycling the Used EquipmentC A U T I O N Rewiring and Reconfiguring the InstallationD A N G E R W A R N I N GTable 13. Communication Options SpecificationsTable 12. Dimensions and Weight ChapterTable 15. Environmental and Safety Table 14. Electrical InputTable 16. Display Optional Main current 6A Table 17. MeteringSPECIFICATIONS All other countries Call your local service representative Chapter 7 TroubleshootingTypical Alarms and Conditions Service and SupportTROUBLESHOOTING Chapter WarrantyLimited Factory Warranty Powerware Energy Management System EMS Upgrade KitWARRANTY Page 1642017241