Manuals / Powerware / Computer Equipment / Power Supply

Powerware 380/220V manual Important Safety Instructions Save These Instructions, Safety Warnings

Models: 415/240V 380/220V 208/120V 400/230V

1 72

Download 72 pages 60.53 Kb

Page 9

Safety Warnings

INTRODUCTION

Safety Warnings

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during installation and operation of the EMS−UGK. Please read all instructions before operating the equipment and save this manual for future reference.

D A N G E R

This EMS−UGK contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the EMS−UGK.

C A U T I O N

STo reduce the risk of fire or electric shock, install this EMS−UGK in a temperature and

humidity controlled, indoor environment, free of conductive contaminants. Ambient temperature must not exceed 40°C (104°F). Do not operate near water or excessive humidity (95% maximum).

SUse the branch circuit breakers to disconnect hazardous voltage from the EMS−UGK. Turn off the breaker before disconnecting the voltage measuring circuit cables, or hazardous voltage may be present at the exposed end of the cable.

SInstallation or use of the equipment in a manner not specified by the manufacturer may impair the protection provided by the equipment.

EATON Powerware® Energy Management System (EMS) Upgrade Kit User’s Guide S 164201724 Rev 1 www.powerware.com

3

Image 9

Powerware 380/220V Important Safety Instructions Save These Instructions, Safety Warnings, D A N G E R, C A U T I O N

Contents

Upgrade Kit 208/120V, 380/220V, 400/230V, 415/240V User’s Guide Powerware Energy Management System EMSRequesting a Declaration of Conformity Three−phase alternating current PROTECTIVE CONDUCTOR TERMINAL Special SymbolsPage Installation Table of ContentsInitial System Configuration Setup OptionsMaintenance Serial Port ServiceSpecifications TroubleshootingIntroduction ChapterThe following options for the EMS−UGK are available Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSD A N G E R C A U T I O NConsignes de sécurité CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONSA T T E N T I O N D A N G E RSicherheitswarnungen WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWARENW A R N U N G A C H T U N GAdvertencias de Seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONESP E L I G R O P R E C A U C I Ó NInspecting the Equipment InstallationUnpacking the Cabinet ChapterVerify that the following items are included with the EMS−UGK Checking the Parts ListS Pliers or other appropriate tool for installing wire taps Tools RequiredTo assemble the components, the following tools may be needed S Phillips #2 screwdriverInstalling the Hardware Verify that at least two wall anchors attach to studs within the wall Figure 4 shows the location of the two serial ports W A R N I N G Electrical ConnectionsC A U T I O N C A U T I O NS If installing conduit not supplied, plan for adequate conduit Table 4. Harness Sizing Figure 5. Wiring Overview Example InstallationA, B, C Panel Connections andFigure 6. Harness Connections at the Electronics Module Table 5. EMS−UGK Harness ConnectionsMain Input Harness CTM Figure 7. Panel Detail EMS−UGK−LV Model with Dual Panel Option Shown INSTALLATIONIf installing dual panels, repeat Step 5 for the second panel Coil and secure any excess cable away from other conductors Install each CT around the appropriate subfeed breaker wire 12. Choose an option for connecting the phases for voltage sensing C A U T I O NC A U T I O N Proceed to Step 15 on page Verify the wire taps are completely closed around the wires 24. Continue to the following section Installing the Software Configuration Tool Initial ConfigurationInitial System Configuration Window Figure 15. System Status Page Connected7. Configure the following required settings voltage. For example, for two 225A panels and a 120V nominalCalc to have the software automatically calculate the VA rating 9. Click Save Sys Config to save the settings to the EMS−UGK. Depending on communication speed, updates take effect within 15-20 seconds 12. Configure the following Miscellaneous Features 13. Configure the following Building Alarm Settingssounds for each new alarm and can be turned off by Configuration Using the Software Configuration Tool 4. Configure the following settings for the selected panel 6. Repeat Steps 3 through 5 to configure the remaining panelsmain panel breaker alarms and zeroes the panel percent 10. Configure the following settings for the selected breaker Initial Panel and Breaker Configuration Using the Display INSTALLATION 12. Continue to the following section, InstallationAdvanced Metering Installation Operation Reset FunctionBreaker Numbering ChapterThe following table shows the indicator status and description Control Panel FunctionsDisplay Functions 000.0 000.0 000.0EATON EMS−UGK PROFILE SETUP SET UPThe following tables show the basic menu structure Menu MapTable 8. Breaker Meters Table 7. Panel MetersUse the arrow keys to enter the password for the level you Setup Optionswant to access, then select DONE to display the options for Use the arrow keys to enter the new password A-ZControl Panel Configuration Accessing ConfigurationConfiguring Panels Containing Branch Circuit Breakers Panel breaker rating in amps Configuring Panels Containing Subfeed BreakersSubfeed breaker rating in amps NOTE Configure a breaker only if its CT is installed Configuring Branch Circuit Breakers7. When all branch circuit configuration is complete, select the Viewing Breaker Meters Viewing Panel MetersChapter 4 Communication Installing Communication Features Serial Port ServiceCommunication Options X−Slot Card Control Terminals Relay Output Contacts Alarm Relay Programmable Signal Inputs Building AlarmsW A R N I N G COMMUNICATION Replacing the Power Xpert Gateway Series 1000 Card MaintenanceRecycling the Used Equipment Updating the FirmwareD A N G E R Rewiring and Reconfiguring the InstallationW A R N I N G C A U T I O NTable 12. Dimensions and Weight SpecificationsChapter Table 13. Communication OptionsTable 15. Environmental and Safety Table 14. Electrical InputTable 16. Display Optional Main current 6A Table 17. MeteringSPECIFICATIONS Typical Alarms and Conditions Chapter 7 TroubleshootingService and Support All other countries Call your local service representativeTROUBLESHOOTING Limited Factory Warranty WarrantyPowerware Energy Management System EMS Upgrade Kit ChapterWARRANTY Page 1642017241