Manuals / Powerware / Computer Equipment / Power Supply

Powerware 380/220V, 400/230V, 415/240V manual Configuration Using the Software Configuration Tool

Models: 415/240V 380/220V 208/120V 400/230V

1 72

Download 72 pages 60.53 Kb

Page 37

INSTALLATION

15.To configure panels and breakers using the software configuration tool, continue to the following section,

Configuration (Using the Software Configuration Tool)."

To configure panels and breakers using the optional display, continue to Step 16.

16.Click Disconnect to disconnect from the EMS−UGK. Verify that Connected" displays at the bottom of the page.

17.Close the software configuration tool and remove the configuration cable.

18.Activate the reset switch on the bottom of the electronics module: hold the switch for 10 seconds or until the display (if installed) turns off, then release the switch.

19.Continue to Display)" on page 34.

Initial Panel and Breaker Configuration (Using the Software Configuration Tool)

To configure the panels and breakers:

1.Click the Panel Config tab to display the EMS Panel Settings page.

2.Verify that the Number of BCM Panels Installed is correct for your installation.

If you change the value, click Save Panel Config to save the setting to the EMS−UGK. Depending on communication speed, updates take effect within 15–20 seconds.

3.Select the panel number to configure (Panel Selected).

EATON Powerware® Energy Management System (EMS) Upgrade Kit User’s Guide S 164201724 Rev 1 www.powerware.com

31

Image 37

Powerware 380/220V, 400/230V, 415/240V, 208/120V manual Configuration Using the Software Configuration Tool

Contents

Upgrade Kit 208/120V, 380/220V, 400/230V, 415/240V User’s Guide Powerware Energy Management System EMSRequesting a Declaration of Conformity Three−phase alternating current PROTECTIVE CONDUCTOR TERMINAL Special SymbolsPage Installation Table of ContentsInitial System Configuration Setup OptionsMaintenance Serial Port ServiceSpecifications TroubleshootingIntroduction ChapterThe following options for the EMS−UGK are available Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSD A N G E R C A U T I O NConsignes de sécurité CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONSA T T E N T I O N D A N G E RSicherheitswarnungen WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWARENW A R N U N G A C H T U N GAdvertencias de Seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONESP E L I G R O P R E C A U C I Ó NInspecting the Equipment InstallationUnpacking the Cabinet ChapterVerify that the following items are included with the EMS−UGK Checking the Parts ListS Pliers or other appropriate tool for installing wire taps Tools RequiredTo assemble the components, the following tools may be needed S Phillips #2 screwdriverInstalling the Hardware Verify that at least two wall anchors attach to studs within the wall Figure 4 shows the location of the two serial ports W A R N I N G Electrical ConnectionsC A U T I O N C A U T I O NS If installing conduit not supplied, plan for adequate conduit Table 4. Harness Sizing Figure 5. Wiring Overview Example InstallationA, B, C Panel Connections andTable 5. EMS−UGK Harness Connections Figure 6. Harness Connections at the Electronics ModuleMain Input Harness CTM Figure 7. Panel Detail EMS−UGK−LV Model with Dual Panel Option Shown INSTALLATIONIf installing dual panels, repeat Step 5 for the second panel Coil and secure any excess cable away from other conductors Install each CT around the appropriate subfeed breaker wire C A U T I O N 12. Choose an option for connecting the phases for voltage sensingC A U T I O N Proceed to Step 15 on page Verify the wire taps are completely closed around the wires 24. Continue to the following section Installing the Software Configuration Tool Initial ConfigurationInitial System Configuration Window Figure 15. System Status Page Connectedvoltage. For example, for two 225A panels and a 120V nominal 7. Configure the following required settingsCalc to have the software automatically calculate the VA rating 9. Click Save Sys Config to save the settings to the EMS−UGK. Depending on communication speed, updates take effect within 15-20 seconds 13. Configure the following Building Alarm Settings 12. Configure the following Miscellaneous Featuressounds for each new alarm and can be turned off by Configuration Using the Software Configuration Tool 6. Repeat Steps 3 through 5 to configure the remaining panels 4. Configure the following settings for the selected panelmain panel breaker alarms and zeroes the panel percent 10. Configure the following settings for the selected breaker Initial Panel and Breaker Configuration Using the Display INSTALLATION 12. Continue to the following section, InstallationAdvanced Metering Installation Operation Reset FunctionBreaker Numbering ChapterThe following table shows the indicator status and description Control Panel FunctionsDisplay Functions 000.0 000.0 000.0EATON EMS−UGK PROFILE SETUP SET UPThe following tables show the basic menu structure Menu MapTable 8. Breaker Meters Table 7. Panel MetersUse the arrow keys to enter the password for the level you Setup Optionswant to access, then select DONE to display the options for Use the arrow keys to enter the new password A-ZAccessing Configuration Control Panel ConfigurationConfiguring Panels Containing Branch Circuit Breakers Panel breaker rating in amps Configuring Panels Containing Subfeed BreakersSubfeed breaker rating in amps NOTE Configure a breaker only if its CT is installed Configuring Branch Circuit Breakers7. When all branch circuit configuration is complete, select the Viewing Breaker Meters Viewing Panel MetersChapter 4 Communication Serial Port Service Installing Communication FeaturesCommunication Options X−Slot Card Control Terminals Programmable Signal Inputs Building Alarms Relay Output Contacts Alarm RelayW A R N I N G COMMUNICATION Replacing the Power Xpert Gateway Series 1000 Card MaintenanceRecycling the Used Equipment Updating the FirmwareD A N G E R Rewiring and Reconfiguring the InstallationW A R N I N G C A U T I O NTable 12. Dimensions and Weight SpecificationsChapter Table 13. Communication OptionsTable 14. Electrical Input Table 15. Environmental and SafetyTable 16. Display Optional Main current 6A Table 17. MeteringSPECIFICATIONS Typical Alarms and Conditions Chapter 7 TroubleshootingService and Support All other countries Call your local service representativeTROUBLESHOOTING Limited Factory Warranty WarrantyPowerware Energy Management System EMS Upgrade Kit ChapterWARRANTY Page 1642017241