Manuals / Powerware / Computer Equipment / Power Supply

Powerware 400/230V, 380/220V, 415/240V manual The following options for the EMS−UGK are available

Models: 415/240V 380/220V 208/120V 400/230V

1 72

Download 72 pages 60.53 Kb

Page 8

The following options for the EMS−UGK are available:

INTRODUCTION

The following options for the EMS−UGK are available:

SSingle panel (42 circuits) or dual panel (84 circuits)

S208/120V or 380/220V, 400/230V, 415/240V rating

SLiquid crystal display (LCD) for local indication of energy usage

SConduit box for enhanced harness protection

SMain input monitoring (three phases and one neutral rated to measure currents up to 400A; up to 100A for input ground)

The following accessories for the EMS−UGK are available:

SSubfeed breaker monitoring, rated to measure currents up to 400A

S100A branch circuit breaker monitoring

STemperature and humidity monitoring with the optional Environmental Monitoring Probe (EMP) that is used with the Power Xpert Gateway Series 1000 Card installed in the EMS−UGK

The EMS−UGK includes an externally−mounted enclosure with an optional display. Current transformers (CTs) provide branch circuit monitoring of installed panelboards. Figure 1 shows an example installation of an EMS−UGK.

Figure 1. Typical EMS−UGK Installation (Dual Panel Shown with Optional Display)

2 EATON Powerware® Energy Management System (EMS) Upgrade Kit User’s Guide S 164201724 Rev 1 www.powerware.com

Image 8

Powerware 400/230V, 380/220V, 415/240V, 208/120V manual The following options for the EMS−UGK are available

Contents

Powerware Energy Management System EMS Upgrade Kit 208/120V, 380/220V, 400/230V, 415/240V User’s GuideRequesting a Declaration of Conformity Special Symbols Three−phase alternating current PROTECTIVE CONDUCTOR TERMINALPage Table of Contents InstallationInitial System Configuration Setup OptionsSerial Port Service MaintenanceSpecifications TroubleshootingChapter IntroductionThe following options for the EMS−UGK are available IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Safety WarningsD A N G E R C A U T I O NCONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS Consignes de sécuritéA T T E N T I O N D A N G E RWICHTIGE SICHERHEITSANWEISUNGEN AUFBEWAREN SicherheitswarnungenW A R N U N G A C H T U N GINSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES Advertencias de SeguridadP E L I G R O P R E C A U C I Ó NInstallation Inspecting the EquipmentUnpacking the Cabinet ChapterChecking the Parts List Verify that the following items are included with the EMS−UGKTools Required S Pliers or other appropriate tool for installing wire tapsTo assemble the components, the following tools may be needed S Phillips #2 screwdriverInstalling the Hardware Verify that at least two wall anchors attach to studs within the wall Figure 4 shows the location of the two serial ports Electrical Connections W A R N I N GC A U T I O N C A U T I O NS If installing conduit not supplied, plan for adequate conduit Figure 5. Wiring Overview Example Installation Table 4. Harness SizingA, B, C Panel Connections andMain Input Harness CTM Figure 6. Harness Connections at the Electronics ModuleTable 5. EMS−UGK Harness Connections INSTALLATION Figure 7. Panel Detail EMS−UGK−LV Model with Dual Panel Option ShownIf installing dual panels, repeat Step 5 for the second panel Coil and secure any excess cable away from other conductors Install each CT around the appropriate subfeed breaker wire C A U T I O N 12. Choose an option for connecting the phases for voltage sensingC A U T I O N Proceed to Step 15 on page Verify the wire taps are completely closed around the wires 24. Continue to the following section Initial Configuration Installing the Software Configuration ToolInitial System Configuration Figure 15. System Status Page Connected WindowCalc to have the software automatically calculate the VA rating 7. Configure the following required settingsvoltage. For example, for two 225A panels and a 120V nominal 9. Click Save Sys Config to save the settings to the EMS−UGK. Depending on communication speed, updates take effect within 15-20 seconds sounds for each new alarm and can be turned off by 12. Configure the following Miscellaneous Features13. Configure the following Building Alarm Settings Configuration Using the Software Configuration Tool main panel breaker alarms and zeroes the panel percent 4. Configure the following settings for the selected panel6. Repeat Steps 3 through 5 to configure the remaining panels 10. Configure the following settings for the selected breaker Initial Panel and Breaker Configuration Using the Display 12. Continue to the following section, Installation INSTALLATIONAdvanced Metering Installation Reset Function OperationBreaker Numbering ChapterControl Panel Functions The following table shows the indicator status and description000.0 000.0 000.0 Display FunctionsEATON EMS−UGK PROFILE SETUP SET UPMenu Map The following tables show the basic menu structureTable 7. Panel Meters Table 8. Breaker MetersSetup Options Use the arrow keys to enter the password for the level youwant to access, then select DONE to display the options for Use the arrow keys to enter the new password A-ZConfiguring Panels Containing Branch Circuit Breakers Control Panel ConfigurationAccessing Configuration Configuring Panels Containing Subfeed Breakers Panel breaker rating in ampsSubfeed breaker rating in amps Configuring Branch Circuit Breakers NOTE Configure a breaker only if its CT is installed7. When all branch circuit configuration is complete, select the Viewing Panel Meters Viewing Breaker MetersChapter 4 Communication Communication Options Installing Communication FeaturesSerial Port Service X−Slot Card Control Terminals W A R N I N G Relay Output Contacts Alarm RelayProgrammable Signal Inputs Building Alarms COMMUNICATION Maintenance Replacing the Power Xpert Gateway Series 1000 CardRecycling the Used Equipment Updating the FirmwareRewiring and Reconfiguring the Installation D A N G E RW A R N I N G C A U T I O NSpecifications Table 12. Dimensions and WeightChapter Table 13. Communication OptionsTable 16. Display Optional Table 15. Environmental and SafetyTable 14. Electrical Input Table 17. Metering Main current 6ASPECIFICATIONS Chapter 7 Troubleshooting Typical Alarms and ConditionsService and Support All other countries Call your local service representativeTROUBLESHOOTING Warranty Limited Factory WarrantyPowerware Energy Management System EMS Upgrade Kit ChapterWARRANTY Page 1642017241