Accessing Internet, IP Address Subnet Mask Gateway | Siemens CL-010

Chapter 3:Accessing Internet

7.Check the network information. Make sure the settings match the settings provided by ISP. Click Finish.

8.Set TCP/IP for your computer. Specify an IP Address, subnet mask and set default gateway. eg:

IP Address: 10.3.75.51

Subnet Mask: 255.255.255.248

Gateway: 10.3.75.49

9.Now the router is well configured. You can access into Internet.

Image 41

Siemens CL-010-I manual Accessing Internet, IP Address Subnet Mask Gateway

Contents

This manual currently suits for CL-010/CL-010-I User’s ManualCL-010/CL-010-I ADSL2+ Router For Installation For Using For Service Safety Notes IC Statement FCC FCC Class B NoticeICES-003 Class B Notice - Avis NMB-003, Classe B ADSL Router User Manual Preface FeaturesATM Features ADSL Compliance Routing Features Bridging FeaturesSecurity Features Configuration and Management Unpacking Subscription for ADSL Service Page Physical Outlook Chapter 1 OverviewLED Indicators Front Panel 9 VAC Rear Panel9VAC Ethernet System Requirement Chapter 2 System Requirement and InstallationChoosing a place for the ADSL Router ™ ™ ™ ™ Connecting the ADSL Router Chapter 3 Configuration Setting TCP/IP For Windows 7. On IP Address tab 9. Wait for Windows copying files 8. When returning to Network window, click OK For Windows ME For Windows NT 5. Click Yes to use DHCP 9. When returning to Network window, click Close Option 2 If you have TCP/IP Protocol, go to Step 5. Click Internet Protocol TCP/IP and then click OK 4. Highlight Protocol and then click Add Panel and then click Network and Internet Connections For Windows XPProperties Click Internet ProtocolTCP/IP and then click OK 9. Click Network and Internet 10. Select Network and Sharing Center For Windows Vista Select Internet Protocol Version 4 TCP/IPv4 and press Properties 11. Click Manage Network Connection on the left side12. Right click Local Area Connection and select Properties Configure PC to get IP address from DHCP For Windows ME Enable Obtain an IP address automatically and then click OK When prompted with the message below, click Yes to continue Windows Vista For Windows 98ME Renew IP Address on Client PC 3. Type cmd in the dialog box and the click OK 2. Select Run from the Start menu 1. From the Start menu, point to Programs, Accessories and then click Command Prompt For Windows Vista Page Chapter 3Connecting and Accessing Internet Chapter 3 Connecting and Accessing Internet Configuration PPP over ATM PPPoA ModePPP over ATM Description Primary IP address192.168.1.1 Subnet Mask255.255.255.0 PPP over ATM PPPoA IP Extension Mode2. Go to Advanced - Internet - Connections. And click Add PPP over Ethernet PPP over Ethernet PPPoE Mode PPP over Ethernet PPPoE IP Extension Mode WAN IP Address WAN Subnet Mask Primary DNS server Numbered IP over ATM IPoASecondary DNS server Primary IP Address Subnet mask Start IP Address End IP Address IP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT Secondary IP Address Subnet mask Primary DNS server Secondary DNS server Unnumbered IP over ATM IPoA IP Address Subnet Mask Gateway Primary IP Address Subnet mask Unnumbered IP over ATM IPoA+NAT Start IP Address End IP Address Bridge Mode Using Web-Based Manager Chapter 4 Web Configuration Outline of Web Manager To Have the New Settings Take EffectLanguage Title Quick Setup Quick StartConnect to Internet Connection TypePage PPP over ATM/ PPP over Ethernet PPP Username PPP PasswordAlways On Dial on Demand End IP Address Start IP AddressLeased Time DHCP Server Off None IP over ATMWAN IP Address WAN Subnet Mask Subnet Mask Primary IP AddressSecondary IP Address Subnet Mask Please wait for 2 minutes for restarting the router Bridging Subnet Mask Overview Status ADSL BER Test ADSL Line Traffic Statistics Internet ConnectionDHCP Table Routing TablePage Local Network- IP Address Advanced SetupLocal Network - DHCP Server Host Name Server and Relay Off Relay On Chapter 5Connection Mode Service Category Internet-Connections SettingLocal Network - UPnP Adding a New One Chapter 5Connection Mode Internet-DNS Server IGMP Proxy EnabledInternet-IGMP Proxy Internet Connection Enable ADSL Port Internet - ADSL SettingsCapability Enabled IP Routing - Static Route Gateway IP Address Configuring Other Routers on Your LANRemove Static Route Local Router IP Routing - Dynamic Routing EnabledExample - Static Route For the Router’s Routing Table Click Apply to invoke the settings set here different interface. Otherwise, disable this function Virtual Server-Port Forwarding Add New Port Forwarding IP Address seen by Internet UsersPre-defined User defined From Internet Host IP Address Connecting to the Virtual ServersVirtual Server-Port Triggering Virtual Server - DMZ Host Virtual Server - Dynamic DNS Password：Dynamic DNS： Internet Connection： Select the direction to filter packets FirewallFiltering by IP address Protocol Allow TrafficSource/Destination IP address Port Range Bridge QoS Quality of ServiceTraffic Class Name 802.1p Priority IPQoS IP type of ServiceSource IP Address/ Subnet Mask Source Port Destination Port Port Mapping Available Interfaces Group Name Diagnostics Management Remote Access Admin AccountSelect the Internet Connection Web Browser Configure System Log UpdateInterntet Time System Log View System Log button Viewing System Log Enable TRAP Service SNMP SettingSNMP Agent Read Community Reset Router Backup ConfigUpdate Firmware http//192.168.1.1/index.html UPnP for XP Chapter 5Connection Mode Problems with WAN Chapter 5 TroubleshootingProblems with LAN Problems with Upgrading ARP Address Resolution Protocol Chapter 6 GlossaryDHCP Dynamic Host Configuration Protocol LAN Local Area Network & WAN Wide Area Network Public IP Address Private IP AddressPVC Permanent Virtual Circuit RIP Routing Information ProtocolPage Chapter 7 Glossary Appendix A Specifications Appendix A Specifications 4. Make sure that Request a certificate is selected, and click Next Appendix B Server Setup for 802.1x ClientGetting Client Certificate Appendix C WEEE - B2C Appendix C WEEE - B2C