![](/images/new-backgrounds/1202138/2021383x1.webp)
IMPORTANT SAFETY INSTRUCTIONS
CAUTION | ! |
ELECTRIC SHOCK HAZARD | |
DO NOT OPEN | |
|
This symbol indicates the possible electric shock hazard associated with uninsulated live components in the interior of the unit.
This symbol indicates the presence of important instructions regarding use and maintenance of the product.
The RTX system consists of two parts connected by a fibre optic cable: the DigiOptical Image Processor and the Display. In this manual references to the “unit” refer to one of the two units that make up the system.
•Read this manual carefully and keep it in a safe place for future consultation.
This manual contains important information on how to install and use this equipment correctly. Before using the equipment, read the safety prescriptions and instructions carefully. Keep the manual for future consultation.
•Do not touch internal parts of the units.
The units contain electrical parts carrying high voltages and operating at high temperatures. Do not remove the cover from the units, refer to qualified service personnel for all repair and maintenance requirements.
The warranty will be automatically invalidated if the cover is removed from the units.
•Power supply disconnect device.
The device for disconnecting the units from the mains power supply is constituted by the power cable plug. Ensure that the power cable plugs and the electrical mains socket outlets are easily accessible during installation operations. To disconnect the units from the electric power supply, pull the plug to remove it from the socket outlet. Do not pull the power cable.
•Use only the specified type of mains power supply. Connect the units to a mains electrical supply with rated voltage of between
Ensure that the power draw of the units is commensurate with the rating of the electrical socket outlets and any extension cables that are used.
For the DigiOptical Image Processor use exclusively the power supply unit provided or an alternative power supply unit expressly approved by SIM2.
•Beware of power supply cables.
Position the power supply cables so that they do not constitute an obstruction.
Position the power supply cables where they cannot be reached by children.
Install the units as close as possible to the wall electrical socket outlet. Do not tread on the power cables, make sure that they are not tangled or pulled; do not expose the power cables to heat sources; make sure that the power cables do not become knotted or kinked. If the power cables become damaged, stop using the system and request the assistance of an authorised technician.
•Disconnect the apparatus from the mains power supply in the event of electrical storms and when not in use. To avoid damage that could be caused by lightning striking in the vicinity of your home, disconnect the units in the event of electrical storms or when the system will remain unused for prolonged periods.
•Avoid contact with liquids and exposure to humidity. Do not use the units near water (sinks, tanks, etc.); do not place objects containing liquids on top of or near the units and do not expose them to rain, humidity, dripping water or spray; do not use water or liquid detergents to clean the units.
•Prevent the units from overheating.
Do not obstruct ventilation openings. Do not place the units near heat sources such as heaters, radiators or other devices that generate heat (including amplifiers). Do not position the units in confined, poorly ventilated places (bookcase, shelves, etc.).
•Do not expose the eyes to the intense light emitted by the lamp.
Never look directly at the lamp through the ventilation opening when the unit is switched on.
Risk of eyesight impairment. Ensure also that children do not look directly at the lamp.
•Position the unit on a stable surface.
To avoid serious injury to persons and damage to property, make sure the units are placed on a level, flat and stable surface from which they cannot fall, tip over or slide. Pay special attention if the units are placed on a trolley so that they can be moved around. Ensure that the units are not subjected to impact.
•Do not insert objects through the units’ openings. Make sure that no objects are inserted inside the units. If this should occur, disconnect the unit from the power supply immediately and call an authorised technician.
•Federal Communication Commission (FCC Statement). This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is used in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determinated by turning the equipment off and on, the user is encuraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
•For customers in Canada
This Class B digital apparatus complies with Canadian
•For customers in the United Kingdom• ATTENTION: This apparatus must be earthed.
The wires in this mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.