5.Pull only the orange/white wire out of the longer piece of conduit on the garage door opener wire harness. Cut the excess length from the orange/white wire to within easy reach of the adapter wire.

6.See Figure 15, the 1 into 1 splice configuration. Use a blue sealed splice connector (Figure 27, Item 5) from the kit to splice the garage door opener wire harness power lead to the adapter wire per the instructions in the service manual appendix.

7.See Figure 27. Install the 2A fuse (11) from the kit into the "OPEN" fuse cavity to complete the circuit.

8.Install the electrical panel per the instructions in the service manual. Install the electrical panel cover by aligning the pins with the rubber bushings in the electrical panel and pushing firmly into place.

9.Proceed to the Yellow and White Lead Connections section for the specific model.

is02589

2

3

 

1

1.CUT this terminal from wire

2.LEAVE this terminal on wire

3.Spring tabs (2)

Figure 17. Fuse Block Adapter Wire (Dyna and Softail)

is06515

Figure 18. "OPEN" Fuse Block Cavity (2004 and Later Dyna)

2003 and Earlier Softail Models

The garage door opener switched power source is the orange/white (O/W) wire in the tail lamp harness under the seat.

1.See Figure 2. Carefully slice open an area of the tail lamp harness (1) wrap at an accessible point under the seat, and cut the orange/white wire.

2.Pull only the orange/white wire out of the longer piece of conduit on the garage door opener wire harness. Cut the excess length from the orange/white wire to within easy reach of the cut orange/white wires under the seat.

3.See Figure 15, the 2 into 1 splice configuration. Use a red sealed splice connector (Figure 27, Item 4) from the kit to splice the garage door opener wire harness power lead to the cut orange/white wires per the instructions in the service manual appendix.

4.Proceed to the Yellow and White Lead Connections section for the specific model.

2004-2010 Softail Models

The garage door opener switched power source is an open fuse position on the fuse panel. See the FUSES section of the service manual and the correct wiring diagram in the service manual appendix.

1.Remove the fuse block cover. Remove the two hex head screws fastening the fuse block bracket, and pull the bracket and fuse block assembly away from the vehicle frame.

2.Press the tab retaining the left fuse block, and slide the block out of the mounting slots.

3.See Figure 27. Get the orange/white fuse block adapter wire (12) from the kit. Note the terminal on each end (see Figure 17). Only the terminal with the spring tabs will fit into this fuse block. Carefully cut the unused terminal from the wire and discard.

4.See Figure 19. Locate the fuse cavity (1) indicated as "P&A IGN" on the fuse block cover in the right fuse block.

Insert the terminal on the orange/white adapter wire until it stops. Refer to a nearby factory installed terminal for comparison to verify proper orientation and depth.

5.Pull only the orange/white wire out of the longer piece of conduit on the garage door opener wire harness. Cut the excess length from the orange/white wire to within easy reach of the adapter wire.

6.See Figure 15, the 1 into 1 splice configuration. Use a blue sealed splice connector (Figure 27, Item 5) from the kit to splice the garage door opener wire harness power lead to the adapter wire per the instructions in the service manual appendix.

7.See Figure 27. Install the 2A fuse (11) from the kit into the "P&A IGN" fuse cavity to complete the circuit.

8.Slide the fuse block into the mounting slots in the fuse block bracket until it clicks firmly into place. Install the bracket and fuse block assembly into position and fasten with the two hex head screws removed earlier. Tighten securely.

9.Proceed to the Yellow and White Lead Connections section for the specific model.

is06516

Figure 19. "P&A IGN" Fuse Block Cavity (2004-2010 Softail)

Sportster Models

The garage door opener switched power source is an orange/white (O/W) main harness power lead inside the elec- trical side cover or under the seat.

-J02028

10 of 16

Page 9 Page 11
Page 10
Image 10
SkyLink 91558-01A, 91561-01, 91562-01 service manual Softail Models, Fuse Block Adapter Wire Dyna and Softail
Page 9 Page 11

91562-01, 91558-01A, 91561-01 specifications

SkyLink has made a remarkable entry into the realm of wireless communication devices with its innovative models: the SkyLink 91562-01, 91558-01A, and 91561-01. Each of these devices is tailored to meet the demands of modern security systems, providing reliability and efficiency for both residential and commercial applications.

The SkyLink 91562-01 stands out for its versatility and ease of use. This wireless communication hub can connect with multiple sensors and devices, enabling a comprehensive security system. Featuring advanced encryption technology, it ensures that communications between the hub and connected devices remain secure from unauthorized access. The 91562-01 supports DIY installation, which means users can easily set up their system without needing professional assistance. Additionally, its sleek design allows it to blend seamlessly into any home decor.

Next, the SkyLink 91558-01A is engineered to provide enhanced connectivity and communication. It features long-range capabilities, allowing it to cover expansive areas without losing signal strength. This model is compatible with a variety of SkyLink sensors and accessories, enabling users to customize their security system according to their specific needs. The 91558-01A is equipped with a built-in backup battery, ensuring that the system remains operational even during power outages, a crucial feature for maintaining security integrity.

Finally, the SkyLink 91561-01 is particularly suited for users who prioritize ease of access and monitoring. With its user-friendly interface, it allows users to manage their security settings and receive real-time alerts from anywhere using a mobile app. This model supports remote access, adding a layer of convenience for those on the go. Moreover, the 91561-01 integrates with smart home devices, providing a holistic approach to home automation and security.

In summary, the SkyLink 91562-01, 91558-01A, and 91561-01 represent a convergence of technology, security, and user-friendliness. With features like long-range communication, innovative encryption, and mobile connectivity, these devices are designed to cater to the dynamic needs of users, ensuring safety and peace of mind in an increasingly connected world. Each model brings its set of strengths to the table, making them suitable for a wide range of applications and user preferences. SkyLink continues to push the envelope in wireless communication and security technology, solidifying its position as a leader in the industry.
Top Page Image Contents