SkyLink Emergency Dialer Dial-Alert, AD-433S manual Entering a premises using the delay dialing

–19–

ADVANCED PROGRAMMING

Entering a premises using the delay dialing

If entering a premises through a door that is monitored with a door sensor, the delay dialing is set to 0 seconds and the dialer is on, the dialer will dial the preprogrammed telephone numbers immediately once that door is opened or any sensor is activated. When the dialer is set to a specified delay, (45 seconds for example) and that door is opened, the dialer will beep for 45 seconds and the screen will flash "dELAY" while the dialer is beeping. This 45 seconds allows you to go to the dialer and deactivate it before it begins to dial. To deactivate the dialer, press and holding the red panic button [o] on the keypad for two seconds. If you have successfully aborted the call, the display will go back to clock mode. If the dialer has not been deactivated within those 45 seconds, the dialer will dial the emergency phone numbers.

To set the dialing delay:

1. Press the [L] key, the display will show “ L ”.

2. Press the [8] key, the display will show “ L 8 1 ”. The last digit is the current delay dialing setting.

3. Press either 1, 2, 3, 4 or 5 to set the delay dialing time, (refer to the chart below)

1	=	0 seconds
2	=	30 seconds
3	=	45 seconds
4	=	60 seconds
5	=	75 seconds

UNIVERSAL DIAL TONE

This feature allows our Dial-Alertto be compatible with all phone systems worldwide. When the Universal Dial Tone is off, our Dial-Alert needs a dial tone before it will dial the pre-programmed telephone numbers. However, not all phone systems and dial tones are the same. For instance, the dial tone may be different for any phone system that accommodates the voice message systems or call answer feature. When the Universal Dial Tone is on, our Dial- Alert will dial no matter what type of dial tone is present. This Universal Dial Tone is factory set to off. However, you may wish to set it to on if your phone line accommodates the voice message systems or call answer feature.

Turn on the universal dial tone:

1. Press the [L] key, display will show “L”.

2. Press the [9] key, display will show “ L 9 1 ”. The last digit (1) indicates that the universal dial tone detection is turned off.

3.Press the [2] key within 5 seconds after pressing the [9] key to turn on the universal dial tone.

ADVANCED PROGRAMMING

When the universal dial tone is turned off, and no dial tone is detected within 1 minute (after the dialer is activated), the display will show “no LInE” and the backlit keypad will flash. To return to standby mode (Display shows the time), press and hold the panic button [O] for 2 seconds.

DIAL SEQUENCE SETTING

During an emergency, the dialer can dial the preprogrammed phone numbers in two different sequences.

1.dials each preprogrammed telephone number once and when the last number is dialed, the dialer goes back to the first phone number. Dials it once then dials the second telephone number once and continues this sequence until the last number is dialed and if the redial is set to "3", it will repeat this sequence one more time.

2.will completely dial the first preprogrammed phone number before dialing the second programmed telephone number. If the redial count is set to "3", the dialer will dial the first telephone number three times, then dial the second number three times and continue with this sequence until all the telephone numbers are dialed.

To program the Dial Sequence Setting

1. Press the [L] key, display will show "L".

2. Press the [0] key, display will show "L0 2" The last digit "2" is the dial setting sequence. It is currently set to dial first number completely, then repeat next sequence.

3. To change the dial setting sequence, enter either "1" or "2" when the display shows "L0 2" (refer to the chart below).

1= dialer dials each phone number once, then repeats sequence.

2= dialer finishes dialing the first phone number, then begins the second number.

–20–