Manuals / Slant/Fin / Household Appliance / Water Heater

Slant/Fin Hydronic Explorer 2 user manual Boiler Selection, Viewing Product Information

Models: Hydronic Explorer 2

1 41

Download 41 pages 49.65 Kb

Page 30

Viewing Product Information

Viewing Product Information

Boiler Selection

The Boiler Selection screen is divided into four panes. The top pane allows you to enter load requirements (Btu/hr) and the type of fuel to be used. The second pane starts off blank but then requests additional information based on the fuel type you selected. The third pane identifies the boilers that meet your requirements, and the fourth panel allows you to select a boiler, cancel, or generate a proposal.

Pane #1: Enter load and fuel type requirements.

Pane #2: Prompts for additional data based on fuel type selected. Also, allows you to view product sheets.

Pane #3: Identifies boilers that meet requirements.

Pane #4: Click OK to accept, Cancel to close screen, or Proposal to generate a proposal.

Boiler Selection Screen

1.Make certain that a value has been entered into the Btu/Hr Load box in pane #1. If there is no value, review section Heat Load is Known or Calculated Heat Load, above.

2.In Fuel Type, click on the down-arrow. A pull-down menu is displayed showing the fuel type choices (natural or propane gas, oil, dual fuel, or electric). Select a fuel type. Depending on the fuel type you select, pane #2 may request additional information, as shown below.

Note: As you make selections in the Boiler Selection Screen, buttons will be displayed in pane #2 allowing you to access relevant product data. You may click on any of these buttons to review the data.

26	Slant/Fin Corporation

Image 30

Slant/Fin Hydronic Explorer 2 user manual Boiler Selection, Viewing Product Information

Contents

Slant/Fin Hydronic ExplorerSlant/Fin Corporation 100 Forest Drive PROPRIETARY INFORMATION NOTICE Slant/Fin CorporationVIEWING PRODUCT INFORMATION Table of ContentsSELECTING A BOILER Slant/Fin CorporationTable of Contents QUICK ANSWERSSlant/Fin Corporation Introduction Using Hydronic ExplorerInstalling Hydronic Explorer Hydronic Explorer User 2 ManualIntroduction Starting Hydronic Explorer Opening the Main MenuSlant/Fin Corporation Page Heat Loss Express Heat Loss ExpressPurpose Slant/Fin CorporationMenu Bar ToolbarHeat Loss Express Data Entry Area Slant/Fin CorporationPerforming Heat Loss Calculations Heat Loss ExpressAdding a Room Adding a FloorSlant/Fin Corporation Entering Room Data Heat Loss ExpressDoor & Glass Factor Room Height, Room Length, and Room WidthDoor & Glass sq ft Exposed Wall LengthCold Partition Length Cold Partition FactorHeat Loss Express Editing and Deleting JobsSlant/Fin Corporation Rooms FloorsHeat Loss Express Selecting Baseboard Room DataSlant/Fin Corporation Selecting Radiant Tubing Description of the Radiant Tubing ScreenHeat Loss Express Heat Loss - Heated Area Slant/Fin CorporationFloor Profile Heat Loss ExpressTubing Calculator Calculating Radiant Tubing RequirementsSlant/Fin Corporation Heat Loss Express Slant/Fin Corporation Radiant Options ComponentsExporting Data Files Printing a HardcopyExporting and Importing Data Files Heat Loss ExpressImporting Data Files Slant/Fin CorporationHeat Loss Express Do the followingLoss Express screen Selecting a BoilerFinding the Right Boiler Slant/Fin CorporationBoiler Selection Viewing Product InformationSlant/Fin Corporation Natural or Propane GasViewing Product Information 5.Select a boiler in pane #3Slant/Fin Corporation Viewing Product Information Generating a ProposalAdditional Components frame. When checked Proposal. The Boiler Proposal screen is12.Click OK to close the Boiler Selection screen Slant/Fin CorporationViewing Product Information Viewing Product InformationObtaining Product Data of that product’s complete catalogHow do I create, edit, or delete a job? Quick AnswersPurpose Slant/Fin CorporationDeleting a floor Adding a floorEditing a floor Adding a roomHow do I save my work? How do I select the right boiler for a job? How do I export job data files?How do I import job data files? How do I select baseboard?How do I select radiant tubing?