Manuals / SMC Networks / Computer Equipment / Network Card

SMC Networks LED Indicators, ABOUT THE Fast Ethernet PCI, 10/100 Mbps Link/Activity, RJ-45

Models: 10/100 Mbps

1 54

Download 54 pages 24.7 Kb

Page 14

LED Indicators

ABOUT THE Fast Ethernet PCI

LED Indicators

The Fast Ethernet PCI includes one status LED indicator, as described in the following figure and table.

10/100 Mbps Link/Activity

Link Act

RJ-45

	Status	Color	Description

	On	Amber	Indicates a valid 10BASE-T link

	Flashing		Indicates 10 Mbps network activity
	Flashing		Indicates 10 Mbps network activity

	On	Green	Indicates a valid 100BASE-TX link

	Flashing		Indicates 100 Mbps network activity
	Flashing		Indicates 100 Mbps network activity

4

Image 14

SMC Networks LED Indicators, ABOUT THE Fast Ethernet PCI, 10/100 Mbps Link/Activity, RJ-45, Status, Color, Description

Contents

On-board socket for optional Boot ROM 10/100 Mbps PCI Adapter with Firewall ProtectionPlug-and-play installation Remote LAN Wakeup support Auto-negotiation of speed and duplex mode Low power consumptionPage June Fast Ethernet PCI User Guide38 Tesla Irvine, CACopyright TrademarksLIMITED WARRANTY LIMITED WARRANTY VCCI Class B Compliance Japan COMPLIANCESFCC - Class B EC Conformance Declaration - Class B COMPLIANCESTroubleshooting TABLE OF CONTENTSInstallation About the Fast Ethernet PCICable Specifications SpecificationsABOUT THE Fast Ethernet PCIFeatures and Benefits ABOUT THE Fast Ethernet PCI1 3-pin connector for Wake-On-LAN cable Hardware Description1 RJ-45 connector for 10/100 Mbps connections 1 Socket for optional boot ROM 1 LED indicator10/100 Mbps Link/Activity LED IndicatorsABOUT THE Fast Ethernet PCI RJ-45Remote LAN Wakeup INSTALLATION Equipment ChecklistHardware Installation HARDWARE INSTALLATIONINSTALLATION Driver Installation INSTALLATION 2. Click “Next.” 3. Check “Specify a location,” and click “Next.”4. Insert the attached CD-ROM into your CD drive, and type E\ assuming E is the location of your CD drive, click “Browse.” 6. Click “OK” to install the driver Software Installation 3. Click “Next” 5. If your system meets the requirements, click “Next” 7. Choose the location where the program icons will be located and click “Next” EtherGuard INSTALLATION 4. Click “Modify Password”7. Click “Enable” or “Disable” to switch the program on and off 12. Sites whose names include words added to this list will be 11. Checking “Name for Site” switches the function on8. Click “Statistic” to view possible intruder activity Note When you input a site name, do not include “http//” Page 17. Check the boxes on the “Protocol Filter” page to block particular protocols WiNeTool Configuration ConfigurationINSTALLATION TX/RX InformationSend Packet Packet Generator Send ACPI Packet Receive Packet - Guage View Set Capture Console ToolbarClick “Analysis” to open the capture console Start Stop Stop & View Filter Setting - MAC Address INSTALLATIONSOFTWARE INSTALLATION Filter Setting - IP AddressFilter Setting - Protocol Sets protocols as filtering criteriaFilter Setting - Pattern Filter Setting - Buffer SizePacket Analysis The packet Analysis screen features three windowsSOFTWARE INSTALLATION The center window shows detailed data on each layerINSTALLATION Receive Packet - DetailTROUBLESHOOTING PCI Compatibilityanother installed card TROUBLESHOOTINGis installed Solutions for Common Problems Network Card Installation ProblemsNetwork Connection Problems Twisted-Pair Cable and Pin Assignments CABLE SPECIFICATIONSCable and Specifications RJ-45 Pin Assignments 1 Tx+ 2 Tx 3 Rx+ 6 RxSPECIFICATIONS Compliances Page FOR LITERATURE OR ADVERTISING RESPONSE, CALL FOR TECHNICAL SUPPORT, CALLINTERNET