Manuals / SMC Networks / Computer Equipment / Network Card

SMC Networks 10/100 Mbps manual RJ-45 Pin Assignments, 1 Tx+ 2 Tx 3 Rx+ 6 Rx

Models: 10/100 Mbps

1 54

Download 54 pages 24.7 Kb

Page 50

RJ-45 Pin Assignments

CABLE SPECIFICATIONS

The figure below illustrates how the pins on the RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins.

With 10BASE-T/100BASE-TX cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. The “+” and “-” signs in the tables below are used to represent the polarity of the wires that make up each wire pair.

RJ-45 Pin Assignments

Pin	Assignment

1Tx+

2Tx-

3Rx+

6Rx-

40

Image 50

SMC Networks 10/100 Mbps manual RJ-45 Pin Assignments, 1 Tx+ 2 Tx 3 Rx+ 6 Rx

Contents

On-board socket for optional Boot ROM 10/100 Mbps PCI Adapter with Firewall ProtectionPlug-and-play installation Remote LAN Wakeup support Auto-negotiation of speed and duplex mode Low power consumptionPage June Fast Ethernet PCI User Guide38 Tesla Irvine, CACopyright TrademarksLIMITED WARRANTY LIMITED WARRANTY VCCI Class B Compliance Japan COMPLIANCESFCC - Class B EC Conformance Declaration - Class B COMPLIANCESTroubleshooting TABLE OF CONTENTSInstallation About the Fast Ethernet PCICable Specifications SpecificationsABOUT THE Fast Ethernet PCIFeatures and Benefits ABOUT THE Fast Ethernet PCI1 3-pin connector for Wake-On-LAN cable Hardware Description1 RJ-45 connector for 10/100 Mbps connections 1 Socket for optional boot ROM 1 LED indicator10/100 Mbps Link/Activity LED IndicatorsABOUT THE Fast Ethernet PCI RJ-45Remote LAN Wakeup INSTALLATION Equipment ChecklistHardware Installation HARDWARE INSTALLATIONINSTALLATION Driver Installation INSTALLATION 2. Click “Next.” 3. Check “Specify a location,” and click “Next.”4. Insert the attached CD-ROM into your CD drive, and type E\ assuming E is the location of your CD drive, click “Browse.” 6. Click “OK” to install the driver Software Installation 3. Click “Next” 5. If your system meets the requirements, click “Next” 7. Choose the location where the program icons will be located and click “Next” EtherGuard INSTALLATION 4. Click “Modify Password”7. Click “Enable” or “Disable” to switch the program on and off 12. Sites whose names include words added to this list will be 11. Checking “Name for Site” switches the function on8. Click “Statistic” to view possible intruder activity Note When you input a site name, do not include “http//” Page 17. Check the boxes on the “Protocol Filter” page to block particular protocols WiNeTool Configuration ConfigurationINSTALLATION TX/RX InformationSend Packet Packet Generator Send ACPI Packet Receive Packet - Guage View Set Capture Console ToolbarClick “Analysis” to open the capture console Start Stop Stop & View Filter Setting - MAC Address INSTALLATIONSOFTWARE INSTALLATION Filter Setting - IP AddressFilter Setting - Protocol Sets protocols as filtering criteriaFilter Setting - Pattern Filter Setting - Buffer SizePacket Analysis The packet Analysis screen features three windowsSOFTWARE INSTALLATION The center window shows detailed data on each layerINSTALLATION Receive Packet - DetailTROUBLESHOOTING PCI Compatibilityanother installed card TROUBLESHOOTINGis installed Solutions for Common Problems Network Card Installation ProblemsNetwork Connection Problems Twisted-Pair Cable and Pin Assignments CABLE SPECIFICATIONSCable and Specifications RJ-45 Pin Assignments 1 Tx+ 2 Tx 3 Rx+ 6 RxSPECIFICATIONS Compliances Page FOR LITERATURE OR ADVERTISING RESPONSE, CALL FOR TECHNICAL SUPPORT, CALLINTERNET