Connecting to a Power Source | SMC Networks SMC8126PL2-F specs

3 Installing the Switch

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the socket located at the back of the device.

Figure 3-6 Power Socket

2.Plug the other end of the cable into a grounded, 3-pin, AC power source.

Note: For international use, you may need to change the AC line cord. You must use a line cord set that has been approved for the receptacle type in your country.

3.Check the front-panel LEDs as the device is powered on to be sure the Power LED is on. If not, check that the power cable is correctly plugged in.

4.If you have purchased a Redundant Power Supply, connect it to the switch and to an AC power source now.

Connecting to the Console Port

The RJ-45 serial port on the switch’s front panel is used to connect to the switch for out-of-band console configuration. The on-board configuration program can be accessed from a terminal or a PC running a terminal emulation program. The pin assignments used to connect to the serial port are provided in the following table.

	8	8
1		8
1		1

Figure 3-7 Serial Port (RJ-45) Pin-Out

3-6

Image 38

SMC Networks SMC8126PL2-F manual Connecting to a Power Source, Connecting to the Console Port

Contents

Installation Guide TigerSwitch 10/100/1000 Installation Guide Page Warranty and Product Registration Compliances and Safety Warnings CE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance France and Peru only France et Pérou uniquement Francia y Perú únicamente Vii Advertencias y mensajes de precaución Purpose Page Contents Appendix a Troubleshooting Contents Tables Figures Xvi Front Panel Network Management Options Switch ArchitecturePower-over-Ethernet Capability SFP Slots Description of Hardware10/100/1000BASE-T Ports Port and System Status LEDs LED Power Supply Socket Mode PoE/Link ButtonOptional Redundant Power Unit Expandability Features and BenefitsConnectivity Performance Introduction to Switching Network Planning Application Examples Collapsed Backbone Network Aggregation Plan Network Aggregation Plan Remote Connections with Fiber Cable Remote Connections with Fiber Cable Making Vlan Connections Making Vlan Connections Application Notes Ethernet Cabling Installing the SwitchSelecting a Site Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack Mounting Installing the Switch in a Rack Desktop or Shelf Mounting Installing an Optional SFP Transceiver Inserting an SFP Transceiver into a Slot Connecting to a Power Source Connecting to the Console Port Wiring Map for Serial Cable Serial Cable Wiring Switch’s 8-Pin Null Modem PC’s 9-Pin Installing the Switch Twisted-Pair Devices Connecting Network DevicesMaking Network Connections Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Network Wiring Connections Network Wiring Connections Fiber Optic SFP Devices Connectivity Rules Making Connections to SFP Transceivers Mbps Fast Ethernet Collision Domain 1000BASE-T Cable RequirementsMbps Gigabit Ethernet Collision Domain Cable Labeling and Connection Records Mbps Ethernet Collision Domain Power and Cooling Problems Appendix a TroubleshootingDiagnosing Switch Indicators Installation In-Band Access 10BASE-T/100BASE-TX Pin Assignments Appendix B CablesTwisted-Pair Cable and Pin Assignments Straight-Through Wiring Crossover Wiring 1000BASE-T Pin Assignments Twisted-Pair Cable and Pin Assignments B Fiber Standards Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling to Run 1000BASE-T Dispersion-Shifted Fiber Cables Appendix C Specifications Physical Characteristics Switch Features Management Features Standards Compliances Specifications Appendix D Ordering Information Ordering Information Glossary 10BASE-T CSMA/CD LED UTP Index Numerics Index-2 Page 150200000032A R01