Regular Maintenance
Deck Rod Timing Adjustment
1. Park the machine on a flat, level surface. Disengage the PTO, engage the parking brake, turn off the engine and remove ignition key. Rear tires must be inflated to 15 psi (1.03 bar); front tires to 25 psi (1.72 bar).
2. To check the lift rod timing, measure and record the distance between the lift pivots and the rod pivots. Repeat for the other side of the unit. See Figure 33.
3. If the measurements for the rods are equal, | Figure 33. Check Lift Rod Timing |
no further adjustment is required. If the |
|
measurements are not equal (greater than 1/8” |
|
(3.17 mm) difference), adjustment is required, |
|
continue with step #4. |
|
4.Lock the deck lift pedal in the 5” (12.7 cm) position. Remove the cutting height adjustment
pin and lower the mower deck.
5. To ensure that the deck is in the lowest position, |
|
| |||
push the pedal by hand towards the rear of the |
|
|
| ||
unit and install the height adjustment pin in the 3” | Figu e 34. | 2 x 4 Locatio s | |||
(7.6 cm) position to hold in place. |
|
| |||
|
|
|
| ||
6. Block up the mower deck until all hanger chains |
|
|
| ||
are slack. Refer to Figure 34. |
|
|
|
|
|
7. See Figure 35. To adjust the lift rod, loosen | he |
|
|
| |
jam nut on the clevis then remove the 1/2” clevis |
|
| |||
|
|
| for |
| |
pin fastening the clevis to the lift pivot arm. Turn |
|
| |||
the clevis clockwise to shorten the distance |
|
|
|
| |
between the rod pivots. Reinstall the clevis | n the |
|
| ||
lift pivot arm and secure with the 1/2” clevis pin |
|
|
| ||
previously removed. Tighten the jam nut against |
|
| |||
the clevis. | Not |
|
| ||
|
|
|
|
| |
8. Remove the blocks from under the mower deck. |
| Figure 35. | Adjust Lift Rod Timing | ||
9. Remove the cutting height adjustment pin from |
|
|
| ||
in front of the deck lift pedal arm. Lift the mow r |
|
| |||
deck and reinstall the adjustment pin in the d sired |
|
| |||
mowing height. |
|
|
|
|
|
Deck Leveling Adjustment |
|
|
|
|
|
NOTE: Before adjusting the deck level,Reprthe deck liftoduction | |||||
rod timing must be checked and/or adjusted. |
|
|
|
|
1.Park the machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1.03 bar); front tires to 25 psi (1.72 bar).
2. | Lock the deck lift pedal in the 5” (12.7 cm) | Figure 36. Hanger Chain Adjustment |
| ||
| position. Place the deck height adjustment pin in |
|
| the 4” position and lower the deck lift pedal until | jam nuts. See Figure 36. |
| the arm contacts the pin. | 5. Loosen the nuts and allow the rear of the deck to |
3. | Place 2 x 4 blocks under each corner of the | rest on the 2 x 4’s. Slide the chains down in the |
| mower deck with the | slots until the chains are tight and tighten the nuts. |
| See Figure 34. | See Figure 36. |
4. | Adjust the front eyebolts until the chains are tight | 6. Remove all 2 x 4 blocks from under the mower |
| and the deck is resting on the 2 x 4’s. Tighten the | deck. |
36 | www.SnapperPro.com |