|
|
| Maintenance |
! | WARNING | ! | 4. Measure the distance (A, Figure 39) between the end of |
the clutch/brake cable (B) and the bottom of the housing | |||
DO NOT attempt any adjustments, maintenance, service or | (C). The measurement should be 3/4”. | ||
repairs with the engine running. STOP engine. STOP blade. | NOTE: The cotter pin, brake spring, and clutch yoke (D, E, | ||
Engage parking brake. Remove key. Remove spark plug | |||
wire from spark plug and secure away from plug. Engine | and F, Figure 39) are noted for reference purposes only. | ||
and components are HOT. Avoid serious burns, allow all |
| ||
parts to cool before working on machine. Fuel Filler Cap |
| ||
must be closed securely to prevent fuel spillage. |
| E | |
|
|
|
Rear Engine Rider Drive |
|
|
|
|
|
|
| ||
Components |
|
|
|
|
|
|
|
| |
Service Brake / Park Brake Adjustment |
| C |
|
|
|
|
| ||
Test the wheel brake on a dry concrete surface. When prop- |
|
|
|
|
|
| |||
erly adjusted, the Rear Engine Rider will stop within 5 feet |
|
|
|
|
|
|
| ||
from fastest speed. If stopping distance is more than 5 feet, |
| E |
|
|
|
|
| ||
the wheel brake should be adjusted as follows: |
|
|
|
|
|
| |||
|
|
|
|
|
| C | |||
1. Follow the WARNING statement found on this page. |
|
|
|
|
|
| |||
2. Carefully stand the Rear Engine Rider on its rear |
| B |
|
|
|
|
| ||
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
| bumper. (See statement below.) |
|
|
|
|
|
| D | |
|
|
|
|
|
|
|
| ||
3. Depress the clutch/brake pedal (A, Figure 38) all the |
|
|
|
|
|
| |||
| D |
|
|
|
|
| |||
| way down. Move and hold the park brake lever (B) in |
| A |
|
|
| |||
|
|
|
|
|
| ||||
| the “ON” position and release the clutch/brake pedal |
|
|
|
|
|
|
| |
| set the park brake. |
|
| Figure 39: Adjusting the brake cable |
| ||||
|
|
| 5. If the measurement is not 3/4”, loosen the two | ||||||
|
|
| |||||||
|
| A |
| (A, Fig re 40). Hold the clutch/brake cable (B) to the | |||||
|
|
|
| chain case bracket. |
| ||||
|
|
| 6. A just the cable up or down using the | ||||||
|
|
|
| obtain a distance of 3/4” between the end of the | |||||
|
|
|
| clutch/brake cable (adjustment shown in inset of Figure | |||||
|
|
|
| 40) and the bottom of the housing. |
| ||||
|
|
| 7. After adjustment is complete, securely tighten the cable | ||||||
|
|
|
|
|
|
|
|
| |
| B |
| 8. Retest the wheel brake. |
| |||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| Figure 38: Setting the park brake | Reproduction |
| ||||||
|
|
| |||||||
| IMPORTANT |
| A |
|
|
|
|
|
To avoid damaging the emissions system:
•Do not overfill the fuel tank. Stop filling the tank when fuel collects in the filler neck.
• Empty the fuel tank before standing the machine on its | B |
rear bumper. |
|
Figure 40: Brake cable adjusting nuts
27