Sonance instruction manual 875D SE Serial Commands, SONAMP 875D SE 8-CHANNELAMPLIFIER

SONAMP® 875D SE 8-CHANNEL AMPLIFIER

875D SE Serial Commands

Serial Protocol: Baud Rate = 9600, N, 8, 1; single CR
Commands In	Syntax	Parameters		State
Power	:Pxy<cr>	x = Zone 1	-4 or G (Global), y = State	0= Off; 1= On
Zone Volume Set	:Vxyyy<cr>	x = Zone 1-4 or G (Global), yyy = Volume 0 - 100		0	(Off) – 100	(Max)
Channel Volume Set	:VCxyyy<cr>	x = Channel 1 - 8 or G (Global), yyy = Volume 0 - 100		0	(Off) – 100	(Max)

NOTE: Issuing a Volume Set command when the amplif ier is OFF will pre - set the zone or channel’s start - up volume to that level .

Zone Volume Incremental Step :Vxyy<cr>	x = Zone 1-4 or G (Global), yy = Volume Step Down/Up	-n = Down, +n = Up; n = 1 to 5
Channel Volume Incremental Step: :VCxyy<cr>	x = Channel 1-8 or G (Global), yy = Volume Step Down/Up	-n = Down, +n + up; n = 1 to 5

NOTE: The 875D SE stores independent settings for Channel and Zone Volume. If Channel Volume commands are sent to a zone that is being controlled with Zone Volume commands (and visa - versa), the volume may initially change to a dif ferent level than expected .

Zone Mute	:Mxy<cr>	x = Zone 1-4 or G (Global), y = State		0	= Mute Off; 1= Mute On
Channel Mute	:MCxy<cr>	x = Channel 1 - 8 or G (Global), y = State		0	= Mute Off; 1 = Mute On
BBE Signal Processing	:BPxy<cr>	x = Zone 1-4	or G (Global), y = State	0= Off; 1= On
BBE HI & LO Frequency Boost	:BBxy<cr>	x = Zone 1-4	or G (Global), y = State	0= +6dB; 1=+9dB
NOTE: The echo for this will provide two values (HI and LO)
BBE HI Frequency Boost	:BHxy<cr>	x = Zone 1-4	or G (Global), y = State	0= +6dB; 1=+9dB
BBE LO Frequency Boost	:BLxy<cr>	x = Zone 1-4	or G (Global), y = State	0= +6dB; 1=+9dB

Adding a question-mark character before the carriage return of any of the above commands will turn the command into a query. Additionally, the following unique queries can also be issued:

Queries	Syntax	Parameters			State
Temperature	:TP?<cr>	–			0 – 100 Degrees C
Audio Trigger Input	:ATIx?<cr>	x = Zone 1-4		or G (Global) [see Notes]	0= Off; 1= On
Fault/Protection	:FPx?<cr>	x = Zone 1	-4	or G (Global) [see Notes]	0= Normal; 1= Fault
Voltage Trigger Input	:VTIx?<cr>	x = Zone 1	-4, A (All) or G (Global) [see Notes]		0= Off; 1= On
Front-Panel Input Control Level	:TVLx?<cr>	x = Channel 1-8 or G (Global) [see Notes]			0 – 100
Firmware Version	:VER?<cr>	–			Version 1.03 or later

(continued on page 16)

15