Settings Detailed and Displays Menu 5 Chapter

VF DISP 2 page

Item

Description

DISP COLOR

Displays the color temperature.

TEMP

 

 

 

DISP BATT

Displays the battery voltage and

REMAIN1)

remaining capacity of an internal

 

battery pack or an external battery

 

connected to the DC IN

 

connector.

 

 

DISP DC IN

Displayed when the power is

 

supplied from an external battery

 

connected to the DC IN

 

connector.

 

 

DISP 16:9/4:3 ID

Displays the 16:9/4:3 mode

 

indicator.

 

 

DISP VTR STATUS

Displays the VTR operating

 

status.

 

 

DISP VTR

Displays the REC TRIGGER

TRIGGER 2)

switch setting.

DISP TIME CODE

Displays the time code.

 

 

DISP REC

Displays the recording format.

FORMAT

 

 

 

1)When an Anton Bauer Intelligent Battery System or a BP-GL65/ GL95/L60S battery pack is used, the setting of this item determines the display as follows.

INT: The remaining battery capacity is shown as a percentage when there is a change, and when the capacity is low.

AUTO: The remaining battery capacity is shown as a percentage, except that when this is impossible the battery voltage appears. VOLT: The battery voltage is shown.

2)Displays only when an external VTR is connected to the (i.LINK) DV OUT connector.

2 Select whether the item should appear in the viewfinder screen (the ON setting), or not appear (the OFF setting).

Display modes and setting change confirmation/adjustment progress messages

You can limit or suppress the messages that give details of setting changes and adjustment progress and results by setting a display mode.

The conditions under which messages are displayed and their correspondence with the display mode are as follows.

Setting change confirmation/adjustment progress messages and display modes

Y: Message is displayed.

N: Message is not displayed.

Message display

Message

Display

 

condition

 

mode

 

 

 

setting

 

 

 

1

2

 

3

When the filter

ND: n

N

N

 

Y

selection has been

(where n = 1, 2, 3, 4)

 

 

 

 

changed

 

 

 

 

 

 

 

 

 

 

 

When the gain setting

GAIN: n

N

N

 

Y

has been changed

(where n = -3dB, 0dB,

 

 

 

 

 

3dB, 6dB, 9dB,12dB,

 

 

 

 

 

18dB, 24dB, 30dB,

 

 

 

 

 

36dB)

 

 

 

 

 

 

 

 

 

 

When the setting of

WHITE: n

N

N

 

Y

the WHITE BAL switch

(where n = A CH, B

 

 

 

 

has been changed

CH, PRESET) or

 

 

 

 

 

ATW: RUN

 

 

 

 

 

 

 

 

 

 

When the OUTPUT/

DCC: ON (or OFF)

N

Y

 

Y

DCC switches has

 

 

 

 

 

been set to DCC ON

 

 

 

 

 

or OFF

 

 

 

 

 

 

 

 

 

 

 

When the shutter

: SS: 1/100 (or 1/125,

N

Y

 

Y

speed and mode

1/250, 1/500, 1/1000,

 

 

 

 

setting has been

1/2000, ECS, SLS)

 

 

 

 

changed*

 

 

 

 

 

 

 

 

 

 

 

When the black or

E.g. WHITE: OK

N

Y

 

Y

white balance has

 

 

 

 

 

been adjusted

 

 

 

 

 

 

 

 

 

 

 

*This is also displayed for about 3 seconds when the SHUTTER switch is set to ON.

To change the display mode

1 Display the VF DISP 1 page of the OPERATION menu.

For details on menu operations, see “Basic menu operations” on page 94.

2 Set VF DISP MODE to either 1, 2, or 3.

The display mode setting changes.

For details about the settings of 1 to 3, see the chart above.

100 Setting the Status Display on the Viewfinder Screen and the LCD Monitor