bTrigger mode
PARA: Operates both internal and external VTRs.
INT: Operates the internal VTR only.
EXT: Operates the external VTR only.
cExtender
“EX” is displayed when a lens extender is used.
dColor temperature
Indicates the currently selected color temperature.
eDC IN / battery voltage / remaining capacity Indicates the battery voltage or the remaining capacity of an attached internal battery pack, an AC adaptor, or an external battery (a battery connected to the DC IN connector).
When the power is supplied from an external battery, “DC IN” appears here.
When the DISP BATT REMAIN item is set to INT on the VF DISP 2 page of the OPERATION menu, the battery voltage is not indicated.
However, when the Anton Bauer intelligent battery system or the
• Until the remaining battery capacity is reduced to 40%, the indications MAX, 90%, 80%...40% are displayed for three seconds in the viewfinder each time the remaining battery capacity reduces by 10%.
• When the remaining battery capacity is less than 40%,
the indication is displayed all the time.
• When the remaining battery capacity is less than 10%*, the indication flashes. When the remaining battery capacity is reduced further, the “LOW” flashes.
*This value can be set to either 10% or 20% on the FUNCTION 2 page of the OPERATION menu.
f* (Asterisk indicator)
Flashes when the color bars are displayed and is recorded together with the color bars.
g16:9 mode recording indicator
Indicates recording in the 16:9 mode. This indicator is recorded together with the color bars.
hSetting change and adjustment progress message display area
For details, see “Display modes and setting change confirmation/adjustment progress messages” on page 100.
iEXT/IV indicator
jRecording format
Indicates the current recording format.
kIris setting/auto iris override
Indicates the F value (iris setting) of the lens.
Also, the auto iris override is displayed using two squares which appear in the upper and lower parts respectively.
For details, see “Adjusting the iris” on page 56.
lRemaining tape capacity
Indicates the remaining tape recording time (in minutes) of the VTR.
Examples of remaining tape recording time indication
Indication | Remaining tape recording time | |
F - 30 | Full to 30 minutes | |
|
|
|
30 | - 25 | 30 to 25 minutes |
|
|
|
25 | - 20 | 25 to 20 minutes |
|
|
|
20 | - 15 | 20 to 15 minutes |
|
|
|
15 | - 10 | 15 to 10 minutes |
|
|
|
10 | - 5 | 10 to 5 minutes |
|
| |
5 - 0 | 5 to 0 minutes | |
|
| |
No display | 0 minute | |
|
|
|
mAudio level
Indicates the level of audio channel 1 and channel 2. The peak indication of the VTR level meter is related as follows to the audio level when an 1kHz sine wave is input.
Audio channel 1 level 
indicator
Audio channel 2 level
indicator
VTR level meter indicator
nOperation/error message display area
For details, see “Operation/error messages” on page 128.
oShutter speed
Indicates the shutter speed or the shutter mode. However, if the SHUTTER switch (page 11) is set to OFF, nothing is displayed.
1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000: Shutter speed (in seconds) in standard mode (scan mode: I)
1/40, 1/60, 1/120, 1/125, 1/250, 1/500, 1/1000, 1/2000:
Shutter speed (in seconds) in standard mode (scan mode: PsF)
ECS: In ECS (Extended Clear Scan) mode
EVS: In EVS (Super Enhanced Vertical Definition System) mode
1F to 8F, 16F
pGain
Indicates the gain of the video amplifier, as set by the GAIN switch.
Overview 1 Chapter
Location and Function of Parts | 23 |
|
|