Manuals / Brands / Photography / Camcorder / Sony / Photography / Camcorder

Sony DSR-400K/400PK, DSR-400L/400PL Attaching a UHF Portable Tuner (for a UHF Wireless Microphone System)

1 141

Download 141 pages, 4.35 Mb

Use the microphone adaptor when using a small- diameter external microphone. When attaching an ECM-670, use the microphone adaptor supplied with these microphone.

Open the CAC-12.

2 Chapter	Loosen the screw.	Microphone adaptor
Preparation

4 Place an external microphone (ECM-670/672/etc. Electret Condenser Microphone or similar microphone) in the CAC-12.

Close the CAC-12.

m	Tighten the screw.	ECM-670/672 or
m		similar microphone

5 Connect the microphone cable to the AUDIO IN CH- 1 or CH-2 connector.

6 Set the switches as follows.

•Set the AUDIO IN input selection switch as indicated below, depending on the type of microphone used.

-When using a microphone with an internal power supply, set it to MIC (center).

-When using a microphone with an external power supply, set it to MIC +48V ON (right).

•Set the AUDIO IN (CH-1/CH-2) switch of the channel that the microphone is connected to REAR.

Monaural microphone

AUDIO IN (CH-1/CH-2)

switchesto AUDIO IN CH-1/CH-2 connector

Notes

•The camcorder can use a microphone with an input level of – 60 dB. Other microphones may not be suitable for use with this camcorder due to differences in the input level.

•In order for the AUDIO IN CH-1 and CH-2 connectors on the camcorder to be able to provide a phantom 48 V power supply, female XLR connectors (3-pin) are fitted. If the microphone cable has a female connector, use an adaptor.

•When you detach a CAC-12 Microphone Holder once you have attached to the camcorder, be careful not to lose the two screws fixing the CAC-12. After detaching the CAC-12, be sure to put the two screws back into their original places.

Attaching a UHF Portable Tuner (for a UHF Wireless Microphone System)

You can use the wireless microphone system including following models to record sound.

•UHF Wireless Microphone

NTSC system: WRT-807B, WRT-847B

PAL system: WRT-807A/B, WRT-847A/B

•UHF Synthesized Transmitter

NTSC system: WRT-8B, WRT-822B

PAL system: WRT-8B, WRT-822A/B

•UHF Synthesizer Tuner

NTSC system: WRR-855B, WRR-861B, WRR-862B

PAL system: WRR-855A/B, WRR-861A/B (in Australia and Asia only), WRR-862A/B

36 Preparing Audio Input System

Contents

Operating Instructions DSR-400L/400PL DSR-400K/400PK DSR-450WSL/450WSPL Owner’s Record WARNING AVERTISSMENT WARNUNG Page Page Table of Contents Recording Analog Composite Signals (with a CBK-SC01Installed DSR-450WS/450WSPonly) Playing and Checking Recorded Contents OverviewChapter1 Product Configurations Features VTR features Location and Function of Parts Right side view Front section Page Left side of the LCD monitor Rear section Operation panel under the AUDIO adjustment cover Left and upper view Page Rear view Page Lens VCL-917BYZoom Lens (DSR-400K/400PKonly) DXF-801Viewfinder Status display on the viewfinder screen Layout of the status display on the viewfinder screen Page Status display on the LCD monitor Page Using the CD-ROM Manual Page Preparation Attaching and Replacing the Lithium Battery Preparing the Lens Preparing a Power Supply Adjusting the Viewfinder To use the camcorder with your left eye Adjusting the viewfinder position To adjust the eyepiece focus To adjust contrast and brightness To adjust the outline emphasis Using the Shoulder Strap Adjusting the Shoulder Pad Position Fitting to a Tripod Using a Video Light Preparing Audio Input System Attaching a UHF Portable Tuner (for a UHF Wireless Microphone System) To attach a WRR-855 To attach a WRR-861/862(When using a BP-GL65/GL95/L60SBattery Pack) Connecting the Remote Control Unit (DSR-450WS/450WSPonly) Function of the REC button when the remote control unit is connected When the monitor is connected to the remote control unit When the remote control unit is disconnected from the camcorder Structure of the paint adjustment data Page Connections Connecting a Monitor Using an i.LINK Connection To check the playback image recorded on an external VTR Using the camcorder as a feeder To copy digitally from the camcorder to the VTR without the editing function To control the camcorder from the VTR using the editing function To control the camcorder from a non-linearediting system Other Connections Recording and Playback Chapter4 Inserting a Cassette Basic Procedure for Shooting Recording To prevent accidental erasure To check the tape for slack Compatibility of DVCAM and DV formats Selecting the recording format Adjusting the black balance/white balance To adjust the black balance To adjust the white balance Setting the electronic shutter About the shutter modes To select the shutter mode and shutter speed Page Adjusting the iris To set the automatic iris To adjust the iris sensitivity Adjusting the audio level To manually adjust the levels of the audio inputs from the AUDIO IN CH-1/CH-2 connectors Setting the time data To save the actual time in the time code To set the user bits To synchronize the time code Page Setting for special shooting cases To correct skin detail Back Space Editing Using the edit search function while back space editing Time-LapseVideo (Interval Rec) Recording Analog Composite Signals (with aCBK-SC01Installed- DSR-450WS/450WSPonly) Playing and Checking Recorded Contents Menu Displays and Detailed Settings Menu Organization and Operation Page Page Page Page Page Page The TOP menu The USER menu The USER MENU CUSTOMIZE menu The ALL menu The OPERATION menu The PAINT menu The MAINTENANCE menu The FILE menu The DIAGNOSIS menu Menu list Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Displaying menus Basic menu operations To select the setting items and values on the menu To end menu operations To display the TOP menu To confirm the setting items and values on the menu Using the USER menu (Example of the menu operation) To cancel setting To return to the standard settings To move to another page Editing the USER menu To add a new page Page To add/delete/replace pages Setting the Status Display on the Viewfinder Screen and the LCD Monitor Display modes and setting change confirmation/adjustment progress messages To change the display mode Setting the marker display Setting the viewfinder Recording shot data superimposed on the color bars To carry out superimposed recording Setting the shot ID To insert a space To delete a character To cancel changing shot ID Displaying the status confirmation windows Display content of the window Adjustments and Settings from Menus Selecting the output signals (DSR-450WS/450WSPonly) Specifying an offset for the auto white balance setting Setting the date/time of the internal clock To cancel the setting Selecting the aspect ratio (DSR-450WS/450WSPonly) Setting the CCD scan mode (DSR-450WS/450WSPonly) Page Saving and Loading the User Setting Data Saving and Loading User Files To protect saved data Notes on using and storing the “Memory Stick” Saving USER menu data (user file) to the “Memory Stick” To set the file ID To select the display contents Loading saved data from a “Memory Stick” Saving and Loading Scene Files White balance setting data saved in the scene file White balance setting data when loading the scene file To save scene files from the camcorder memory to the “Memory Stick” Loading scene files Resetting the settings of the camcorder to the standard settings Displaying a File-Related Menu Page When Stick” Appendix Important Notes on Operation About the LCD panels Phenomena specific to CCD image sensors Condensation Maintenance To confirm the result About i.LINK About a “Memory Stick” Precautions Operation Warnings Page Error code list Operation/error messages Troubleshooting Page Specifications Microphone Tape section Input/output connectors VCL-917BYZoom Lens (supplied with the DSR-400K/400PK) Pin assignment of the connectors Related Products Chart of Optional Components and Accessories For DSR-450WS/450WSP Glossary Page Index