To connect

Do this

 

DVD player with

Connect to the component sockets

component output

and the audio sockets

/ 4.

EThe component signal containing 576p signal format and audio signal are input from the DVD player.

Digital satellite

Connect to the HDMI IN 5 socket

receiver or DVD

if the equipment has a HDMI

 

player F

socket. The digital video and audio

 

signals are input from the digital

 

satellite receiver. If the equipment

 

has a DVI socket but not an HDMI

 

socket, connect the DVI socket to

 

the HDMI IN 5 socket through a

 

DVI - HDMI adaptor interface (not

 

supplied), and connect the

 

 

equipment’s audio out sockets to

 

the audio in HDMI IN 5 sockets.

 

The digital video and analogue

 

 

audio signals are input from the

 

 

equipment.

 

 

 

 

 

 

 

“PlayStation 2”,

Connect to the scart socket

/

DVD player or

 

1. When you connect the

 

 

 

decoder G

decoder, the scrambled signal from

 

the TV tuner is output to the

 

 

decoder, then the unscrambled

 

 

signal is output from the decoder.

 

In this case, it will be properly

 

 

unscrambled if you set “AV2

 

 

Output” to “TV” (page 27).

 

 

 

 

 

 

DVD recorder or

Connect to the scart socket

/

VCR that supports

 

2. SmartLink is a direct link

 

SmartLink H

between the TV and a VCR/DVD

 

recorder. For more information on

 

SmartLink, refer to the instruction

 

manual supplied with your VCR or

 

DVD recorder.

 

 

 

 

 

 

VCR I

For details, see page 11.

 

 

 

 

 

 

Hi-Fi audio

Connect to the audio output

 

equipment J

sockets

 

to listen to the sound

 

 

from the TV on Hi-Fi audio

 

 

equipment. To turn off the sound

 

of the TV speakers, set “Speaker”

 

to “Off” (page 26).

 

 

 

 

 

 

 

Programming the remote

This remote is preset to operate Sony TVs, most Sony DVDs, VCRs and AUX systems (DAV, DTT Receiver, Home Theatre, etc.). To control VCRs and DVDs of other manufacturers (and some other Sony VCR, DVD and AUX models), do the following procedure to programme the remote.

Note

Before you start, look up the three-digit code for your brand of DVD, VCR or AUX system from the “Manufacturer’s codes” on page 37.

 

AUX/VIDEO

TV

 

R

U

1

 

V D

 

 

T

VD

 

C

 

A

 

 

X

 

V

 

 

DIGITAL MODE

1

2

3

 

4

5

6

2

7

8

9

 

 

0

 

 

1 To programme VCR or DVD:

Press and hold for about six seconds until the green VCR and DVD lights flash.

To programme Sony AUX systems:

Press and hold for about six seconds until the green AUX light flashes.

2 While the relevant lights are flashing, press the number buttons to enter all three digits of the code for your brand of equipment (page 38).

The green light is lit momentarily.

3 Turn on your equipment and check that the following main functions work.

N(playback), x (stop), m (rewind), M (fast forward), channel selection for both VCR and DVDs, Menu and M/m/</, buttons only for DVDs.

If your equipment is not working, or some of the functions do not work

Enter the correct code or try the next code listed for the brand. However, not all brands are covered and not all models of every brand may be covered.

36 GB