(1) Power ON, current probe method:

 

18.3 A (100 V), 37.1 A (240V)

 

(2) Hot switching inrush current,

 

measured in accordance with

 

European standard EN55103-1:

 

35.5 A (230 V)

 

LMD-2450W:

 

(1) Power ON, current probe method:

 

21.8 A (100 V), 40.6 A (240V)

 

(2) Hot switching inrush current,

 

measured in accordance with

 

European standard EN55103-1:

 

38.8 A (230 V)

Dimensions

LMD-2050W: Approx. 518.5 × 468.4

 

× 269.9 mm (including the

 

projection parts)

 

(20 1/2 × 18 1/2 ×10 3/4 inches)

 

(w/h/d)

 

LMD-2450W: Approx. 602.4 × 497.9

 

× 269.9 mm (including the

 

projection parts)

 

(23 3/4 × 19 5/8 × 10 3/4 inches)

 

(w/h/d)

Mass

LMD-2050W: Approx. 10.1 kg (22 lb

 

4 oz) (when no input adaptor is

 

installed)

 

Approx. 10.5 kg (23 lb 2 oz) (when two

 

BKM-229X are installed)

 

LMD-2450W: Approx. 11.0 kg (24 lb

 

4 oz) (when no input adaptor is

 

installed)

 

Approx. 11.4 kg (25 lb 2 oz) (when two

 

BKM-229X are installed)

Operating conditions

Temperature0 °C to 35 °C (32 °F to 95 °F) Recommended temperature

 

20 °C to 30 °C (68 °F to 86 °F)

Humidity

30 % to 85 % (no condensation)

Pressure

700 hPa to 1060 hPa

Storage and transport conditions

Temperature–20 °C to + 60 °C (–4 °F to 140 °F)

Humidity

0 % to 90 %

Pressure

700 hPa to 1060 hPa

Accessories supplied

AC power cord (1) AC plug holder (1) Operating Instructions (1) CD-ROM (1)

Warranty Card (1)

Using the CD-ROM Manual (1) Optional accessories

SDI 4:2:2 input adaptor BKM-220D

HD/D1-SDI input adaptor BKM-243HS

NTSC/PAL input adaptor BKM-227W

Analog component input adaptor

BKM-229X

Mounting bracket

MB-529 (for LMD-2050W)

Design and specifications are subject to change without notice.

Note

Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.

Pin assignment

1 8

PARALLEL REMOTE connector

Modular connector

(8-pin)

Pin number

Functions

1

Designating composite input signal

 

 

2

Designating component input signal

 

 

3

Setting tally lamp green ON/OFF

 

 

4

Setting tally lamp red ON/OFF

 

 

5

GND

 

 

6

Selecting external sync.

 

 

7

Selecting over scan

 

 

8

Selecting normal scan

 

 

You can allocate functions using the REMOTE menu (see page 29).

Wiring required to use the Remote Control Connect the function you want to use with a Remote Control to the Ground (Pin 5).

SERIAL REMOTE (RS-232C) connector

D-sub 9 pin, female

51

9 6

Pin number

Signal

1NC

Specifications 33