Notes
•The VOR system depends on the environment conditions. If you cannot get the desired results, set VOR to OFF.
•When using the VOR system, the unit starts recording only when a sound is detected, therefore, the beginning of the word may not be recorded. For an important recording, we recommend setting VOR to OFF.
To monitor the sound
Connect an earphone (supplied) firmly to the EAR jack. The sound for monitoring cannot be adjusted by VOL.
Start recording during playback
Press r(record) during playback, recording starts immediately. It is useful when you want to
Review the portion just recorded
Push up CUE/0•)/REVIEW toward )REVIEW during recording. Release the button at the point to start playback.
Recording cue markers
While recording, you can record a special signal on the tape to mark a specific position.
At the desired position, press CUE MARKER to record a signal. The REC lamp goes off and a signal will be recorded on the tape. If you want to record a signal longer than that, press CUE MARKER as long as you want. During cue and review, you will hear the beep sound at the signal position. During playback, you will hear the signal with low frequency sound at the signal position.
Notes
•We recommend recording cue markers when there is a break in the sound.
•During cue and review, the beep sounds differently.
•The beep may sound differently depending on the marked position on the tape because the winding speed varies from the beginning to the end of the tape.
At the end of the tape
In the recording or playback mode, the tape stops at the end of the tape and the locked buttons will be released automatically (Automatic
Recording/Playback with the Connected Equipment
Notes
•When connecting cords, be sure you connect plugs firmly.
•The example uses Sony products. If you have any problem when using other products, read the instruction manual of those products.
Recording from another tape recorder G-a
Set this unit to the recording mode and another tape recorder to the playback mode. In this case set VOR to OFF.
Dubbing onto another tape recorder G-b
Set this unit to the playback mode and another tape recorder to the recording mode.
Recording with an external microphone G-c
Connect a microphone to MIC. When using a
zAdditional Information
Precautions
On powerOperate the unit only on 3V DC. For AC operation, use the AC power adaptor recommended for the unit. Do not use any other type. For battery operation, use two size AA (R6) batteries.
On the unit•Use only the y(standard microcassetes) with this unit. Nonstandard cassette cannot be used because the “L” dimension (see Fig. A) is different.
To prevent a tape from being accidentally recorded over (see Fig. F)Break out and remove the cassette tabs. To reuse the tape for recording, cover the tab hole with adhesive tape.
•Do not leave the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.
•Should any solid object or liquid fall into the unit, remove the batteries or disconnect the AC power adaptor, and have the unit checked by qualified personnel before operating it any further.
•When you do not use the unit for long, remove the batteries to avoid damage caused by battery leakage and subsequent corrosion.
•If the unit has not been used for a long time, set it in the playback mode and warm it up for a few minutes before inserting a tape.
Keep personal credit cards using magnetic coding or
If you have any questions or problems concerning your unit, please consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks, consult your nearest Sony dealer.
You cannot insert the cassette.mThe cassette is inserted front side back.
m9(play) is pressed.
You cannot close the cassette compartment lid.mThe cassette is inserted into the wrong part (it should be inserted into the lid side).
m9(play) is pressed.
Playback is not possible even if you press 9 (play).mThe tape has reached the end. Rewind the tape.
mThe batteries are weak. Replace both batteries with new ones.
You cannot press r (record).mThere is no cassette.
mThe tab on the tape has been removed. To reuse the tape for recording, cover the tab hole with adhesive tape.
You cannot press r (record) and 9 (play).mThe tape has reached the end. Rewind the tape.
mAfter the atuomatic
mThe batteries are weak. Replace both batteries with new ones.
mThe head is contaminated.
mVOR has been set to the improper position when VOR function works.
Recording is interrupted.mVOR is set to L or H. When you do not use VOR, set it to OFF.
Recording cannot be erased completely.mThe head is contaminated.
During CUE0/)REVIEW the tape stops or does not run.You cannotmThe batteries are weak. Replace both batteries with new ones.
The unit does not operate.mThe batteries have been inserted with incorrect polarity.
mThe batteries are weak. Replace both batteries with new ones.
mCPAUSE is slid in the direction of the arrow.
mThe AC power adaptor or car battery cord is not firmly connected.
mThe batteries have been inserted, but simultaneously the AC power adaptor is connected and not to be done to the wall outlet.
No sound comes from the speaker.mThe earphone is plugged in.
mThe volume is turned down completely.
The sound drops out, sound quality becomes worse or sound has excessive noise.mThe volume is turned down completely.
mThe batteries are weak. Replace both batteries with new ones.
mThe head is contaminated.
Tape speed is too fast or too slow in the playback mode.mImproper setting of the TAPE SPEED switch. Set it to the same speed as that used for recording.
Tape speed is faster than the normal playback speed.mThe FAST PB switch is slid in the direction of the arrow.
Maintenance I
To clean the tape head and pathPress 9(play) and wipe the head 1, capstan 2 and the pinch roller 3 with a cotton swab, moistened with alcohol every 10 hours of use.
To clean the exteriorUse a soft cloth slightly moistened in water. Do not use alcohol, benzine or thinner.