Playing MDs

Fade-out playback

During playback, press FADE at the position where you want fade-out playback to start.

“FADE OUT” flashes in the display and the deck performs fade-out recording until the counter reaches “0.0s.”

The deck changes to play pause when fade-out playback finishes.

Note on the peak level meters display during fade- in/fade-out playback

The peak level meters show the level of the original signal (input from the LINE(ANALOG) IN connectors or output to the LINE(ANALOG ) OUT connectors and the PHONES connector). Therefore, the level shown on the meters does not increase or decrease ever as the output fades in or out.

zYou can set the duration of fade-in and fade-out playback independently

Do Steps 1 to 5 in “You can set the duration of the fade- in and fade-out recording independently” on page 18.

zYou can select the type of increment/decrement curve for fade-in/fade-out recording

Do Steps 1 to 4 in “You can select the type of increment/decrement curve for fade-in/fade-out recording” on page 18.

Playing an MD Using a Timer

By connecting a timer (not supplied) to the deck, you can start and stop playback operations at specified times. For further information on connecting the timer or setting the starting and ending times, refer to the instructions that came with the timer.

TIMER

 

 

 

 

 

 

 

 

EDIT/

 

￿AMS ±

DIGITAL

REC LEVEL

 

 

ANALOG

 

POWER

 

 

 

 

 

 

 

NO

YES

 

0

•

 

 

4

• 5

•

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•

 

 

 

 

 

 

 

 

 

 

 

 

•

3

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

•

 

 

 

 

 

•

g

 

 

 

 

 

 

 

0 )

 

•

•

2•

 

 

 

 

 

•8

 

 

 

 

 

 

 

 

 

 

•

 

1

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

–

+

•

0

 

 

10

TIMER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PUSH ENTER

 

 

 

 

 

L

R

 

 

REC OFF PLAY

 

 

 

INPUT

 

SCROLL/

DISPLAY/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FILTER

CLOCK SET

CHAR

 

 

 

 

 

 

 

 

 

 

 

PHONES

PHONE LEVEL

OPT2

OPT1

• COAX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•ANALOG

 

 

 

§

(

P

p

 

 

 

r

 

 

 

 

 

 

 

 

 

PLAY MODE

REPEAT

TIME

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OPEN/CLOSE

 

 

 

 

 

 

REC

 

 

 

 

0

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PLAY MODE

(

1Do Steps 1 to 3 in ”Playing an MD” on page 7.

2Press PLAY MODE repeatedly (or one of the PLAY MODE buttons once) to select the play mode you want.

To play only specific tracks, create a program (see page 24).

3• If you want to specify the time for the start of playback, go to Step 4.

•If you want to specify the time for the end of playback, press (to start playback, then go to

Step 4.

•If you want to specify the time for both start and end of playback, go to Step 4.

4Set TIMER on the deck to PLAY.

5Set the timer as required.

•When you have set the time for the start of playback, the deck turns off. When the specified time arrives, the deck turns on and starts playing.

•When you have set the time for the end of playback, playback continues. When the specified time arrives, the deck stops playing and turns off.

•When you have set the time for both the start and end of playback, the deck turns off. When the starting time arrives, the deck turns on and starts playing. When the ending time arrives, the deck stops playing and turns off.

6After you have finished using the timer, set TIMER on the deck to OFF.

Note

You can select Program Play in Step 2. Note, however, that programs eventually fade away when the standby status is off, and therefore if you set the time too far in the future, the program may be gone when the specified time arrives. If this has occurred, the deck enters normal play mode at the specified time and the tracks play in consecutive order.

28EN