Trouble symptoms and remedies
If a problem occurs as a result of a connected computer or other equipment, refer to the connected computer/equipment’s instruction manual. Use the
Symptom | Check these items |
No picture
If the 1 (power) indicator is not lit, or if the 1 (power) indicator will not light up when the 1 (power) switch is pressed,
•Check that the power cord is properly connected.
•Check that the monitor’s MAIN POWER switch is “on” (page 9).
The 1 (power) indicator turns on red. | • Check that the 1 (power) switch is on. |
|
|
If the 1 (power) indicator is green, | • Use the |
|
|
If CABLE DISCONNECTED | • Check that the video signal cable is properly connected and all plugs are firmly seated in |
appears on the screen, | their sockets (page 7). |
| • Check that the video input connector’s pins are not bent or pushed in. |
| • Check that the input select setting is correct (page 11). |
| • A |
| signal cable, CABLE DISCONNECTED may appear on the screen before entering the |
| power saving mode. This is not a malfunction. |
|
|
If NO INPUT SIGNAL appears on | • Check that the video signal cable is properly connected and all plugs are firmly seated in |
the screen, or the 1 (power) | their sockets (page 7). |
indicator is orange, | • Check that the video input connector’s pins are not bent or pushed in. |
| • Check that the input select setting is correct (page 11). |
| xProblem caused by a connected computer or other equipment, and not |
| caused by the monitor |
| • The computer is in the power saving mode. Try pressing any key on the keyboard or |
| moving the mouse. |
| • Check that your graphics board is attached to the computer properly. |
| • Check that the computer’s power is “on.” |
|
|
If OUT OF SCAN RANGE appears | xProblem caused by a connected computer or other equipment, and not |
on the screen (page 19), | caused by the monitor |
| • Check that the video frequency range is within that specified for the monitor. If you |
| replaced an old monitor with this monitor, reconnect the old monitor and then adjust the |
| computer’s graphics board in the following ranges. |
| Horizontal frequency: 28 – 61 kHz |
| Vertical frequency: 56 – 75 Hz |
| Resolution: 1024 × 768 or less |
|
|
If using Windows, | • If you replaced an old monitor with this monitor, reconnect the old monitor and do the |
| following. Select “SONY” from the “Manufacturers” list and select |
| X72” or |
| X52” or |
| or install the information file for this monitor using the Windows Monitor Information Disk. |
|
|
If using a Macintosh system, | • When connecting a Macintosh computer, use an adapter (not supplied) if necessary. |
| Connect the adapter to the computer before connecting the video signal cable. |
Picture flickers, bounces, oscillates, or is scrambled.
•Adjust the pitch and phase (analog RGB signal only) (page 13).
•Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors, laser printers, electric fans, fluorescent lighting, or televisions.
•Move the monitor away from power lines or place a magnetic shield near the monitor.
•Try plugging the monitor into a different AC outlet, preferably on a different circuit.
•Change the orientation of the monitor.
xProblem caused by a connected computer or other equipment, and not caused by the monitor
•Check your graphics board manual for the proper monitor setting.
•Confirm that the graphics mode (VESA, Macintosh 19'' Color, etc.) and the frequency of the input signal are supported by this monitor. Even if the frequency is within the proper range, some graphics boards may have a sync pulse that is too narrow for the monitor to sync correctly.
•This monitor does not process the interlace signals. Set for progressive signals.
•Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture (60 Hz is recommended).
20
