Receiver Operations

Receiving Broadcasts

This receiver lets you enter a station’s frequency directly by using the numeric buttons on the remote (direct tuning). If you don’t know the frequency of the station you want, see “Receiving broadcasts by scanning stations (automatic tuning)”.

Before you begin, make sure you have:

•Connected an FM/AM aerial to the receiver as indicated on page 5.

•Set the SPEAKERS button to ON.

?/1 (power)

MASTER VOLUME TUNING +/–

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TUNER

FM/AM

FM MODE

To receive other stations

Repeat Steps 3 to 5.

If the STEREO indicator remains off

Press FM MODE when an FM stereo broadcast is received.

If an FM stereo programme is distorted

The STEREO indicator flashes. Press FM MODE to change to monaural (MONO). You will not have the stereo effect but the distortion will be reduced. To return to stereo mode, press this button again.

If you cannot tune in a station and the entered numbers are flashing

Make sure you’ve entered the right frequency. If not, press D. TUNING and re-enter the frequency you want on the remote. If the entered numbers still flash, the frequency is not used in your area.

To watch FM simulcast TV programmes

Make sure that you tune in the simulcast programme both on the TV (or the VCR) and on the receiver.

numeric buttons

D. TUNING

1Press ?/1(power) to turn on the receiver.

2Press TUNER.

The last received station is tuned in.

3Press FM/AM to select FM or AM stations.

4Press D. TUNING on the remote.

5Press the numeric buttons on the remote to enter the frequency.

Example 1: FM 102.50 MHz Example 2: AM 1350 kHz

1

0

2

5

0

1

3

5

0

0

6When you tune in AM stations, adjust the direction of the AM loop aerial for optimum reception.

If you enter a frequency not covered by the tuning interval

The entered value is automatically rounded up or down to the closest covered value.

Tuning intervals for direct tuning are:

FM: 50 kHz intervals

AM: 9 kHz intervals

Receiving broadcasts by scanning stations (automatic tuning)

If you don’t know the frequency of the radio station you want, you can have the receiver scan all the receivable stations to locate the one you want.

1Press TUNER.

The last received station is tuned in.

2Press FM/AM to select FM or AM.

3Press TUNING + or –.

Press the + button for a higher frequency; press the – button for a lower one. When you tune past either end of the band, the receiver automatically jumps to the opposite end. Every time a station is received, the receiver stops scanning. To continue scanning, press the button again.

13GB