VPL-AW15
VPL-AW10
For customers in the USA
Declaration of Conformity
Disposal of Used Lamp
For customers in the United States
Trademark Information
Page
Table of Contents
Location of Controls
Connections and
Preparations
Projecting
Others
On safety
On preventing internal heat buildup
Caution
On repacking
Location of Controls
Page
Page
Connections and Preparations
Before Setting Up the
Projector
Improper use
Do not do any of the following while using the projector
Blocking the ventilation holes
Tip
Tilting front/rear and left/right
Positioning the Projector and a screen
When using the 16:9 aspect ratio screen
When using the 4:3 aspect ratio screen (projecting a 4:3 picture)
2 Position the projector so that the lens is parallel to the screen
Top view
Connecting to a VCR
Page
To connect to a VCR equipped with the S video connector or video connector
Connecting to a Computer
1 After connecting the AC cord to the equipment, plug the AC cord
into a wall outlet
2 Press the ?/1 (On/standby) switch to turn on the projector
3 Turn on the equipment connected to the projector
4 Press INPUT to project the picture on the screen
5 Move both LENS SHIFT dials (VPL-AW15only) to adjust the picture position
To adjust the horizontal position
To adjust the vertical position
6 Adjust the picture size using the zoom lever
7 Adjust the focus using the focus ring
To adjust the tilt of the installation surface
1 Press MENU
2 Press M/m to select the Setup menu, and press , or
3 Press M/m to select “Language,” and press , or
4 Press M/m/</, to select a language, and press
To clear the menu
Projecting
Turning Off the Power
Wide Zoom
Normal
Full
Zoom
Full 1 (When the PC signal is input)
Full 2 (When the PC signal is input)
Notes on selecting the wide screen mode
Press one of the PICTURE MODE buttons
(DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3)
DYNAMIC
STANDARD
CINEMA
1 Press ADJ PIC
2 Make the setting or adjustment
on an item
When changing the adjustment
level
1 Press RCP on the remote control
2 Press M/m to select “User 1,” “User 2” or “User 3,” then press
3 Select the target color you want to adjust
4 Adjust the color of the specified portions
5 After the adjustment is complete, press
Press PIC MUTING
Press FREEZE
Using the Menus
2 Press M/m to select a menu item, and press , or
3 Press M/m to select an item you want to set or adjust and press
,or
4 Make the setting or adjustment of an item
When changing the adjustment level
Items that cannot be adjusted
To reset the picture that has been adjusted
To reset the items that have been adjusted
Adjust Picture menu
Page
Page
Page
Adjust Screen menu
Page
Page
Page
Page
Page
About the Preset Memory No
Others
Power
Picture
On-screendisplay
Remote control
Others
Warning Indicators
Message Lists
Warning messages
Caution messages
Tools you need to get started:
Standard Phillips screwdriver
Cloth (for scratch protection)
1 Turn off the projector and unplug the AC power cord
6Close the lamp cover, then tighten the screws
7Remove the air filter cover
8Remove the air filter
Attach the air filter cover
Wipe dust off the Ventilation holes (intake) with a soft cloth
Place the project back on its original position
Place a new air filter
Select “Yes”
Page
System
Input
General
Supplied accessories
Optional accessories
Preset Signals
Page
Preset memory numbers for each input signal
Analog signal
Digital signal
Input Signals and Adjustable/Setting Items
Screen menu
When Using the PSS-H10Projector Suspension Support
When using the 4:3 aspect ratio screen
Attaching the PSS-H10projector suspension support
Top view
Front view
Side view
When Using the PSS-610Projector Suspension Support
Attaching the PSS-610projector suspension support
