Sony VPL-AW10, VPL-AW15 Adjust Screen menu

Screen Menu

The Screen menu is used to adjust the input signal. You can adjust the size of the picture, and select wide screen mode, etc.

.

Adjust Screen menu

Wide Mode (When the You can set the aspect ratio of the picture to be displayed for the input signal is moving current input signal. This item is enabled only when a moving

picture)picture (preset memory numbers 1 to 14) (1 page 61) is provided. Wide Zoom: A 4:3 aspect ratio picture is enlarged over the entire screen

properly. The upper and lower portions of the screen are slightly cut off.

Normal: A picture with normal 4:3 aspect ratio is displayed in the center of the screen to fill the vertical screen size.

Full: A picture squeezed to 4:3 is displayed with the correct aspect ratio. A 4:3 picture is enlarged horizontally to fit the 16:9 screen.

Zoom: A normal 16:9 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen.

Wide Mode (When the You can set the aspect ratio of the picture to be displayed for the

PC signal is input) current input signal. This item is enabled only when an PC signal is input.

Full 1: Displays a picture on the whole of the screen without changing the aspect ratio of the original picture.

Full 2: Displays a picture on the whole of the screen.

Zoom: A normal 16:9 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen.

Over Scan	Hides the outline of the picture.
	On: Hides the outline of the input picture. Select this setting when noise
	appears along the edge of the picture.
	Off: Projects the whole of the input picture.
	Tip
	To adjust the display area, refer to “Blanking” on the installation
	menu (1 page 49). (VPL-AW15 only)

44

Contents

VPL-AW15 VPL-AW10 For customers in the USA Declaration of Conformity Disposal of Used Lamp For customers in the United States Trademark Information Page Table of Contents Location of Controls Connections and Preparations Projecting Others On safety On preventing internal heat buildup Caution On repacking Location of Controls Page Page Connections and Preparations Before Setting Up the Projector Improper use Do not do any of the following while using the projector Blocking the ventilation holes Tip Tilting front/rear and left/right Positioning the Projector and a screen When using the 16:9 aspect ratio screen When using the 4:3 aspect ratio screen (projecting a 4:3 picture) 2 Position the projector so that the lens is parallel to the screen Top view Connecting to a VCR Page To connect to a VCR equipped with the S video connector or video connector Connecting to a Computer 1 After connecting the AC cord to the equipment, plug the AC cord into a wall outlet 2 Press the ?/1 (On/standby) switch to turn on the projector 3 Turn on the equipment connected to the projector 4 Press INPUT to project the picture on the screen 5 Move both LENS SHIFT dials (VPL-AW15only) to adjust the picture position To adjust the horizontal position To adjust the vertical position 6 Adjust the picture size using the zoom lever 7 Adjust the focus using the focus ring To adjust the tilt of the installation surface 1 Press MENU 2 Press M/m to select the Setup menu, and press , or 3 Press M/m to select “Language,” and press , or 4 Press M/m/</, to select a language, and press To clear the menu Projecting Turning Off the Power Wide Zoom Normal Full Zoom Full 1 (When the PC signal is input) Full 2 (When the PC signal is input) Notes on selecting the wide screen mode Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3) DYNAMIC STANDARD CINEMA 1 Press ADJ PIC 2 Make the setting or adjustment on an item When changing the adjustment level 1 Press RCP on the remote control 2 Press M/m to select “User 1,” “User 2” or “User 3,” then press 3 Select the target color you want to adjust 4 Adjust the color of the specified portions 5 After the adjustment is complete, press Press PIC MUTING Press FREEZE Using the Menus 2 Press M/m to select a menu item, and press , or 3 Press M/m to select an item you want to set or adjust and press ,or 4 Make the setting or adjustment of an item When changing the adjustment level Items that cannot be adjusted To reset the picture that has been adjusted To reset the items that have been adjusted Adjust Picture menu Page Page Page Adjust Screen menu Page Page Page Page Page About the Preset Memory No Others Power Picture On-screendisplay Remote control Others Warning Indicators Message Lists Warning messages Caution messages Tools you need to get started: Standard Phillips screwdriver Cloth (for scratch protection) 1 Turn off the projector and unplug the AC power cord 6Close the lamp cover, then tighten the screws 7Remove the air filter cover 8Remove the air filter Attach the air filter cover Wipe dust off the Ventilation holes (intake) with a soft cloth Place the project back on its original position Place a new air filter Select “Yes” Page System Input General Supplied accessories Optional accessories Preset Signals Page Preset memory numbers for each input signal Analog signal Digital signal Input Signals and Adjustable/Setting Items Screen menu When Using the PSS-H10Projector Suspension Support When using the 4:3 aspect ratio screen Attaching the PSS-H10projector suspension support Top view Front view Side view When Using the PSS-610Projector Suspension Support Attaching the PSS-610projector suspension support