Manuals / Brands / Computer Equipment / Projector / Sony / Computer Equipment / Projector

Sony VPL-VW50 Projecting, Example:, 1 Power on both the equipment and the device connected to the equipment

1 80

Download 80 pages, 2.16 Mb

Projecting

This section describes how to operate the projector to view the picture from the equipment connected to the projector. It also describes how to adjust the quality of the picture to suit your taste.

Projecting the Picture on the Screen

LIGHT INPUT

DYNAMIC STANDARD CINEMA

1 Power on both the equipment and the device connected to the equipment.2 Press INPUT repeatedly to select the input you want to project on the screen.

Display the indication of the input you want.

Example: To view the picture from the video equipment connected to the VIDEO INPUT connector.

To view the picture from	Press INPUT to display

Video equipment connected to the VIDEO INPUT connector	Video

Video equipment connected to S VIDEO INPUT connector	S-Video

Component equipment connected to Y/CB/PB/CR/PR on the projector	Component

RGB/component equipment connected to the INPUT A connector	Input-A*

Equipment connected to the HDMI1 connector	HDMI1

Equipment connected to the HDMI2 connector	HDMI2

*Set the “Input-A Signal Sel.” setting in the Setup menu according to the signal input. When you set it to “Auto,” and cannot display the picture properly, select an appropriate signal according to the input signal. (1 page 48, 52)

Tip

When “Auto Input Search” is set to “On” in the Function menu, the input terminal with effective signals is automatically displayed by pressing INPUT.

28

Contents

VPL-VW50 For customers in the USA Declaration of Conformity Disposal of Used Lamp For customers in the United States Page Table of Contents Location of Controls Connections and Preparations Projecting Others On safety On preventing internal heat buildup Caution On repacking Location of Controls Page Page Connections and Preparations Before Setting Up the Projector Improper use Do not do any of the following while using the projector Blocking the ventilation holes Tip Tilting front/rear and left/right Positioning the Projector and a screen When using the 16:9 aspect ratio screen When using the 4:3 aspect ratio screen (projecting a 4:3 picture) 2 Position the projector so that the lens is parallel to the screen Top view Connecting to a VCR Page To connect to a VCR equipped with the S video connector or video connector Connecting to a Computer Page 2 Press the ?/1 (ON/STANDBY) switch to turn on the projector 3 Turn on the equipment connected to the projector 4 Press INPUT to project the picture on the screen 5 Adjust the vertical picture position 6 Adjust the picture size 7 Adjust the focus To adjust the tilt of the installation surface Page Page To clear the menu Projecting Turning Off the Power Press WIDE MODE Full Normal Wide Zoom Zoom Full 1 (When the PC signal is input) Full 2 (When the PC signal is input) Notes on selecting the wide screen mode Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3) DYNAMIC STANDARD CINEMA To adjust contrast and brightness 1 Press ADJ PIC 2 Make the setting or adjustment on an item 1 Press RCP on the remote control 2 Press M/m to select “User 1,” “User 2” or “User 3,” then press 3 Select the target color you want to adjust 4 Adjust the color of the specified portions 5 After the adjustment is complete, press ENTER Using the Menus 1 Press MENU 2 Press M/m to select a menu item, and press , or ENTER ,or ENTER 4 Make the setting or adjustment of an item To reset the items that have been adjusted Items that cannot be adjusted Adjust Picture menu Page Page Page Adjust Screen menu Page Page Page Page Page Page About the Preset Memory No Others Power Picture On-screendisplay Remote control Others Warning Indicators Message Lists Warning messages Caution messages Tools you need to get started: Standard Phillips screwdriver Cloth (for scratch protection) 1 Turn off the projector and unplug the AC power cord Page Place the project back on its original position Attach the filter holder Wipe dust off the Ventilation holes (intake) with a soft cloth 14 Select “Yes” 15Select “OK” Page System Input General Supplied accessories Optional accessories Preset Signals Page Preset memory numbers for each input signal Analog signal Digital signal Input Signals and Adjustable/Setting Items Screen menu When Using the PSS-H10Projector Suspension Support When using the 4:3 aspect ratio screen Attaching the PSS-H10projector suspension support Top view Front view Side view When Using the PSS-610Projector Suspension Support Attaching the PSS-610projector suspension support Page Tools you need to get started Phillips screwdriver: 110 mm (4 3/8 inches) or longer Flat-headscrewdriver: 110 mm (4 3/8 inches) or longer When using the 16:9 screen 5 Attach the ring (washer) by turning it clockwise