Manuals / Brands / Computer Equipment / Projector / Sony / Computer Equipment / Projector

Sony VPL-VW50 Preset Signals, Warning on power connection

1 80

Download 80 pages, 2.16 Mb

Warning on power connection

Use a proper power cord for your local power supply.

	The United States,	Continental Europe	UK, Ireland,	Japan
	Canada		Australia, New
			Zealand

Plug type	YP-3	YP-12A	*	YP-359

Female end	YC-13	YC-13D	VM0303B	YC-13

Cord type	SVT	H05VV-F	CEE (13) 53 rd	VCTF
			(OC)

Rated Voltage	10A/125V	10A/250V	10A/250V	12A/125V		Others
& Current

Safety approval	UL/CSA	VDE	VDE	DENANHO

* Use a rated plug that complies with the regulation of each country/region and the specifications.

Preset Signals

The following table shows the signals and video formats which you can project using this unit.

When a signal other than the preset signal shown below is input, the picture may not be displayed properly.

Memory	Preset signal		fH (kHz)	fV (Hz)	Sync	H Size
No.

1	VIDEO/60	60 Hz	15.734	59.940	–	–

2	VIDEO/50	50 Hz	15.625	50.000	–	–

3	480/60i	DTV 480/60i	15.734	59.940	SonG/Y or composite	–
					sync

4	576/50i	DTV 576/50i	15.625	50.000	SonG/Y or composite	–
					sync/composite video

5	480/60p	480/60p	31.470	60.000	SonG/Y	–
		(Progressive
		NTSC)

6	576/50p	576/50p	31.250	50.000	SonG/Y	–
		(Progressive PAL)

7	1080/60i	1035/60i, 1080/60i	33.750	60.000	SonG/Y	–

8	1080/50i	1080/50i	28.130	50.000	SonG/Y	–

9	1080/24PsF	1080/48i	27.000	48.000	SonG/Y	–

10	720/60p	720/60p	45.000	60.000	SonG/Y	–

11	720/50p	720/50p	37.500	50.000	SonG/Y	–

12	1080/60p	1080/60p	67.500	60.000	–	–

13	1080/50p	1080/50p	56.260	50.000	–	–

63

Contents

VPL-VW50 For customers in the USA Declaration of Conformity Disposal of Used Lamp For customers in the United States Page Table of Contents Location of Controls Connections and Preparations Projecting Others On safety On preventing internal heat buildup Caution On repacking Location of Controls Page Page Connections and Preparations Before Setting Up the Projector Improper use Do not do any of the following while using the projector Blocking the ventilation holes Tip Tilting front/rear and left/right Positioning the Projector and a screen When using the 16:9 aspect ratio screen When using the 4:3 aspect ratio screen (projecting a 4:3 picture) 2 Position the projector so that the lens is parallel to the screen Top view Connecting to a VCR Page To connect to a VCR equipped with the S video connector or video connector Connecting to a Computer Page 2 Press the ?/1 (ON/STANDBY) switch to turn on the projector 3 Turn on the equipment connected to the projector 4 Press INPUT to project the picture on the screen 5 Adjust the vertical picture position 6 Adjust the picture size 7 Adjust the focus To adjust the tilt of the installation surface Page Page To clear the menu Projecting Turning Off the Power Press WIDE MODE Full Normal Wide Zoom Zoom Full 1 (When the PC signal is input) Full 2 (When the PC signal is input) Notes on selecting the wide screen mode Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3) DYNAMIC STANDARD CINEMA To adjust contrast and brightness 1 Press ADJ PIC 2 Make the setting or adjustment on an item 1 Press RCP on the remote control 2 Press M/m to select “User 1,” “User 2” or “User 3,” then press 3 Select the target color you want to adjust 4 Adjust the color of the specified portions 5 After the adjustment is complete, press ENTER Using the Menus 1 Press MENU 2 Press M/m to select a menu item, and press , or ENTER ,or ENTER 4 Make the setting or adjustment of an item To reset the items that have been adjusted Items that cannot be adjusted Adjust Picture menu Page Page Page Adjust Screen menu Page Page Page Page Page Page About the Preset Memory No Others Power Picture On-screendisplay Remote control Others Warning Indicators Message Lists Warning messages Caution messages Tools you need to get started: Standard Phillips screwdriver Cloth (for scratch protection) 1 Turn off the projector and unplug the AC power cord Page Place the project back on its original position Attach the filter holder Wipe dust off the Ventilation holes (intake) with a soft cloth 14 Select “Yes” 15Select “OK” Page System Input General Supplied accessories Optional accessories Preset Signals Page Preset memory numbers for each input signal Analog signal Digital signal Input Signals and Adjustable/Setting Items Screen menu When Using the PSS-H10Projector Suspension Support When using the 4:3 aspect ratio screen Attaching the PSS-H10projector suspension support Top view Front view Side view When Using the PSS-610Projector Suspension Support Attaching the PSS-610projector suspension support Page Tools you need to get started Phillips screwdriver: 110 mm (4 3/8 inches) or longer Flat-headscrewdriver: 110 mm (4 3/8 inches) or longer When using the 16:9 screen 5 Attach the ring (washer) by turning it clockwise